Toyota Tacoma (2015-2018) Service Manual: Removal
REMOVAL
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
- When removing the front fender wheel opening moulding or quarter panel wheel opening moulding, heat the vehicle body and front fender wheel opening moulding or quarter panel wheel opening moulding using a heat light.
|
Item |
Temperature |
|---|---|
|
Vehicle Body |
40 to 60°C (104 to 140°F) |
|
Front Fender Wheel Opening Moulding or Quarter Panel Wheel Opening Moulding |
20 to 30°C (68 to 86°F) |
NOTICE:
Do not heat the vehicle body or front fender wheel opening moulding or quarter panel wheel opening moulding excessively.
PROCEDURE
1. REMOVE FRONT FENDER MUDGUARD (w/ Mudguard)
(See page .gif)
)
2. REMOVE FRONT FENDER WHEEL OPENING MOULDING (w/ Mudguard)
|
(a) Using a heat light, heat the front fender wheel opening moulding. |
|
(b) Remove the 4 screws.
(c) Disengage the 3 claws and 9 clips, and peel off the double-sided tape to remove the front fender wheel opening moulding.
3. REMOVE FRONT FENDER WHEEL OPENING MOULDING (w/o Mudguard)
|
(a) Using a heat light, heat the front fender wheel opening moulding. |
|
(b) Remove the 7 screws.
(c) Disengage the 3 claws and 9 clips, and peel off the double-sided tape to remove the front fender wheel opening moulding.
4. REMOVE REAR QUARTER PANEL MUDGUARD (w/ Mudguard)
(See page )
5. REMOVE QUARTER PANEL WHEEL OPENING MOULDING (w/ Mudguard)
|
(a) Using a heat light, heat the quarter panel wheel opening moulding. |
|
(b) Remove the 3 screws.
(c) Disengage the 10 clips, and peel off the double-sided tape to remove the quarter panel wheel opening moulding.
6. REMOVE QUARTER PANEL WHEEL OPENING MOULDING (w/o Mudguard)
|
(a) Using a heat light, heat the quarter panel wheel opening moulding. |
|
(b) Remove the 7 screws.
(c) Disengage the 10 clips, and peel off the double-sided tape to remove the quarter panel wheel opening moulding.
Reassembly
REASSEMBLY
CAUTION / NOTICE / HINT
HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
When installing a new front wheel opening ex ...
Installation
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
When installing a new front fender wheel o ...
Other materials:
Transfer Shift Motor Limit Switch Circuit (P17AC)
DESCRIPTION
When the transfer switches modes, the TL1, TL2 and TL3 terminals of the limit
switch are in one of the ON/OFF combinations listed in the table below.
Terminal
When 2WD
Switching between 2WD and H4
When H4
Switching between H4 and ...
Brake Switch "A" Circuit (P0571)
DESCRIPTION
Detection condition 1:
When the brake pedal is depressed, the stop light switch assembly outputs
a signal to the ECM. When the ECM receives the signal, it cancels control
of vehicle speed by the dynamic radar cruise control system. The fail-safe
function operates to ...
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
If a DTC is displayed during the DTC check, check the parts listed in
the table below and proceed to the "See page" given.
*1: "Comes on" means the Malfunction Indicator Lamp (MIL) illuminates.
*2: "DTC stored" means ...
