Toyota Tacoma (2015-2018) Service Manual: Freeze Frame Data
FREEZE FRAME DATA
DESCRIPTION
(a) Whenever a forward recognition camera system DTC is stored, the forward recognition camera stores the current vehicle state (ECU and sensor information) as Freeze Frame Data.
CHECK FREEZE FRAME DATA
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.
(e) According to the display on the Techstream, select a DTC with freeze frame data.
(f) Read the freeze frame data recorded when the DTC was stored.
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Blockage Status |
Camera obstruction malfunction status |
ON or OFF |
ON: Forward recognition camera obstructed OFF: Forward recognition camera not obstructed |
- |
|
Blockage History |
Camera obstruction history status |
ON or OFF |
ON: Forward recognition camera obstruction history exists OFF: Forward recognition camera obstruction history does not exist |
- |
|
Low Temperature Status |
Low temperature malfunction status |
ON or OFF |
ON: Forward recognition camera low temperature malfunction exists OFF: Forward recognition camera low temperature malfunction does not exist |
- |
|
Low Temperature History |
Low temperature history status |
ON or OFF |
ON: Forward recognition camera low temperature history exists OFF: Forward recognition camera low temperature history does not exist |
- |
|
High Temperature Status1 |
High temperature malfunction status |
ON or OFF |
ON: Forward recognition camera high temperature malfunction exists OFF: Forward recognition camera high temperature malfunction does not exist |
- |
|
High Temperature History1 |
High temperature history status |
ON or OFF |
ON: Forward recognition camera high temperature history exists OFF: Forward recognition camera high temperature history does not exist |
- |
|
High Temperature Status2 |
- |
- |
- |
This item is displayed on the Techstream but is not used. |
|
High Temperature History2 |
- |
- |
- |
This item is displayed on the Techstream but is not used. |
|
Backlight Status |
Backlight Status |
Driving Backlight or OFF |
Driving Backlight: Driving towards the sun OFF: Not driving towards the sun |
- |
|
Vehicle Information (2WD/4WD) |
Vehicle information (drivetrain) stored in forward recognition camera |
2WD, 4WD or Unknown |
2WD: for 2WD 4WD: for 4WD Unknown: Vehicle information not confirmed |
- |
|
Vehicle Information (Conv/HV) |
Vehicle information (conventional/hybrid) stored in forward recognition camera |
Conv, HV or Unknown |
Conv: Conventional HV: Hybrid vehicle Unknown: Vehicle information not confirmed |
- |
Fail-safe Chart
FAIL-SAFE CHART
FAIL-SAFE FUNCTION
(a) If a malfunction is detected in the forward recognition camera system, the
systems that use the forward recognition camera perform the fail-safe function. ...
Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches,
sensors, actuators and other items to be read without removing any part ...
Other materials:
Pattern Select Switch
Components
COMPONENTS
ILLUSTRATION
Removal
REMOVAL
PROCEDURE
1. REMOVE INSTRUMENT PANEL LOWER CENTER FINISH PANEL
(See page )
2. REMOVE PATTERN SELECT SWITCH ASSEMBLY
(a) Detach the 2 claws to remove the pattern select switch assembly from
the instrument panel lower c ...
Brake System (P157800)
DESCRIPTION
This DTC is output when the VSC system has a problem. Check the VSC system when
this DTC is output.
DTC No.
DTC Detection Condition
Trouble Area
MIL
Note
P157800
Diagnosis Condition:
Cr ...
Clutch Switch Circuit
DESCRIPTION
While depressing the clutch pedal, the clutch start switch assembly sends a signal
to terminal MTN of the 4 wheel drive control ECU. While the signal is input, switching
between H4 and L4 is possible.
WIRING DIAGRAM
PROCEDURE
1.
READ VALUE USING TECHSTREA ...
