DESCRIPTION
If the manual up/down function can be performed but the auto up/down function cannot, then the fail-safe mode may be functioning.
If the power window initialization (See page ) has not been performed, the auto up/down function will not operate.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
HINT:
If the pulse sensor built into the front power window regulator motor assembly LH is malfunctioning, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the power window regulator master switch assembly at the auto up position, and opened manually by pushing down the power window regulator master switch assembly (See page ).
Click here
PROCEDURE
1. |
READ VALUE USING TECHSTREAM (MASTER SWITCH) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Master switch / Data List.
(e) Read the Data List according to the display on the Techstream.
Master Switch
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
---|---|---|---|
D Door P/W Auto SW |
Driver side power window auto up/down switch signal / ON or OFF |
ON: Driver side power window auto switch operated OFF: Driver side power window auto switch not operated |
- |
OK:
On the Techstream screen, ON or OFF is displayed accordingly.
NG |
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY |
|
2. |
READ VALUE USING TECHSTREAM (D-DOOR MOTOR) |
(a) Enter the following menus: Body Electrical / D-Door Motor / Data List.
(b) Read the Data List according to the display on the Techstream.
D-Door Motor (Front Power Window Regulator Motor Assembly LH)
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
---|---|---|---|
D Door P/W Auto SW |
Driver side power window auto up/down switch signal / ON or OFF |
ON: Driver side power window auto switch operated OFF: Driver side power window auto switch not operated |
- |
OK:
On the Techstream screen, ON or OFF is displayed accordingly.
NG |
GO TO STEP 5 |
|
3. |
PERFORM INITIALIZATION (for Driver Side) |
(a) Initialize the front power window regulator motor assembly LH (See page ).
|
4. |
CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION) |
(a) Check that the driver side door power window moves when the auto up/down function of the power window regulator master switch assembly is operated (See page ).
OK:
Driver side auto up/down function is normal.
OK |
END (PROBLEM DUE TO INITIALIZATION FAILURE) |
NG |
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH |
5. |
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY |
(a) Replace the power window regulator master switch assembly (See page ).
|
6. |
CHECK AND REPLACE POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION) |
(a) Check that the driver side door power window moves when the auto up/down function of the power window regulator master switch assembly is operated (See page ).
OK:
Driver side auto up/down function is normal.
OK |
END (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WAS DEFECTIVE) |
NG |
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH |
Disassembly
DISASSEMBLY
PROCEDURE
1. REMOVE TELEPHONE MICROPHONE ASSEMBLY
Click here
2. REMOVE MICROPHONE CASE
HINT:
Use the same procedure for Double Cab.
Click here
3. REMOVE NO. 1 ROOF WIRE (w/ Vanity Light)
(a) w/ EC Mirror:
(1) Remove the No. 1 roof wire.
...
Automatic High Beam Camera (B124C)
DESCRIPTION
The main body ECU (multiplex network body ECU) detects a high beam headlight
illumination request signal of the automatic high beam system from the forward recognition
camera
DTC No.
Detection Item
DTC Detection Condition
Trouble Area
...
Data List / Active Test
DATA LIST / ACTIVE TEST
1. DATA LIST
Using the Techstream to read the Data List allows the values or states of switches,
sensors, actuators and other items to be read without removing any parts. This non-intrusive
inspection can be very useful because intermittent conditions or signals may be ...