Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Customize Parameters

CUSTOMIZE PARAMETERS

PROCEDURE

1. CUSTOMIZE INTUITIVE PARKING ASSIST SYSTEM

(a) Customizing with the Techstream

NOTICE:

  • When the customer requests a change in a function, first make sure that the function can be customized.
  • Be sure to make a note of the current settings before customizing.
  • When troubleshooting a function, first make sure that the function is set to the default setting.

(1) Connect the Techstream to the DLC3.

(2) Turn the ignition switch to ON.

(3) Turn the back sonar or clearance sonar switch assembly on.

(4) Turn the Techstream on.

(5) Enter the following menus: Body Electrical / Utility / Customize / Sensor

(6) Select the setting by referring to the table below.

Warning

Display

Default

Content

Setting

Relevant ECU

Rr Sensor Onset Range

Wide

Sets the buzzer activation range for the rear center sensors.

Narrow or Wide

  • Narrow: 1000 mm (39.3 in.)
  • Wide: 1400 mm (55.1 in.) (Pole)
  • Wide: 1800 mm (70.9 in.) (Wall)

Clearance warning ECU assembly

Keep Sense Buzzer

Avail

Sounds the buzzer when the distance between the vehicle and obstacle does not change for more than 3 seconds.

Not Avail or Avail

  • Not Avail: Not Available
  • Avail: Available

Clearance warning ECU assembly

Fr & Rr Buzzer Volume

M2

Changes the buzzer volume setting.

L, M1, M2, M3 or H

  • L: Low volume
  • M1: Medium low volume
  • M2: Medium volume
  • M3: Medium high volume
  • H: High volume

Clearance warning ECU assembly

Sensor

Display

Default

Content

Setting

Relevant ECU

Sensor Condition N

Avail

Makes the front sensors available when the shift lever is in N.

Not Avail or Avail

  • Not Avail: Not Available
  • Avail: Available

Clearance warning ECU assembly

Non P/R Range Rear Sensor

R Stop

Changes the operation setting for the rear sensors when the shift lever is in any position other than P or R.

R, Rcrn or R Stop

  • R: All rear sensors are available
  • Rcrn: Rear corner sensors are available
  • R Stop: All rear sensors are not available

Clearance warning ECU assembly

Operation Check
OPERATION CHECK 1. MALFUNCTION DISPLAY (MULTI-INFORMATION DISPLAY) (a) Open circuit indication (1) If there is an open circuit between a No. 1 ultrasonic sensor and the clearance warning ECU asse ...

Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are lis ...

Other materials:

Inspection
INSPECTION PROCEDURE 1. INSPECT NO. 1 ULTRASONIC SENSOR (a) Measure the resistance according to the value(s) in the table below. Text in Illustration *a Component without harness connected: (No. 1 Ultrasonic Sensor) Standar ...

Tire Pressure Warning Receiver
Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. SEPARATE ROOF HEADLINING ASSEMBLY (for Double Cab) (See page ) 2. SEPARATE ROOF HEADLINING ASSEMBLY (for Access Cab) (See page ) 3. REMOVE TIRE PRESSURE WARNING ECU AND RECEIVER (a) Disconnect the connector. (b) ...

Short in Driver Side Squib 2nd Step Circuit (B1810/53-B1813/53)
DESCRIPTION The driver side squib 2nd step circuit consists of the airbag sensor assembly, the spiral cable with sensor sub-assembly and the horn button assembly. The circuit signals the SRS to deploy when airbag deployment conditions are met. These DTCs are set when a malfunction is detected i ...

В© 2011-2024 Copyright www.ttguide.net