Toyota Tacoma (2015-2018) Service Manual: Customize Parameters

Toyota Tacoma (2015-2018) Service Manual / Door Lock / Power Door Lock Control System / Customize Parameters

CUSTOMIZE PARAMETERS

1. CUSTOMIZE POWER DOOR LOCK CONTROL SYSTEM

HINT:

The following items can be customized.

NOTICE:

When the customer requests a change in a function, first make sure that the function can be customized.
Be sure to make a note of the current settings before customizing.
When troubleshooting a function, first make sure that the function is set to the default setting.

(a) Customizing with the Techstream

(1) Connect the Techstream to the DLC3.

(2) Turn the ignition switch to ON.

(3) Turn the Techstream on.

(4) Enter the following menus: Customize Setting / Door Lock.

(5) Select the setting by referring to the table below.

Display	Default	Content	Setting	Relevant ECU
Unlock Key Twice	ON	Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlocks all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors.	OFF or ON	Main body ECU (Multiplex network body ECU)
Automatic Door Lock Function	Link Shift	Link Shift: Function that locks all doors when the shift lever is moved out of P, with the ignition switch ON and all doors closed. Link Speed: Function that locks all doors when the vehicle speed reaches a certain level.	OFF, Link Shift or Link Speed	Main body ECU (Multiplex network body ECU)
Automatic Door Unlock Function	Link Shift	Link D-door: Function that unlocks the other doors when the driver door is opened within approximately 43 seconds of the ignition switch being turned off. Link Shift: Function that unlocks all doors when the shift lever is moved to P from any position other than P with the ignition switch ON.	OFF, Link D-door or Link Shift	Main body ECU (Multiplex network body ECU)

(b) Customizing with the Multi-display

(1) Turn the ignition switch to ON.

(2) Enter the following menus: APPS / Setup / Vehicle / Vehicle Customization / Door Lock Settings. (for Navigation Receiver Type)

(3) Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door Lock Settings. (for Radio and Display type)

(4) Select the setting by referring to the table below.

Display	Default	Content	Setting	Relevant ECU
Automatic Door Lock Function	By Shift From P	By Shift From P: Function that locks all doors when the shift lever is moved out of P, with the ignition switch ON and all doors closed. By Speed: Function that locks all doors when the vehicle speed reaches a certain level.	OFF, By Shift From P or By Speed	Main body ECU (Multiplex network body ECU)
Automatic Door Unlock Function	By Shift to P	By Driver Door: Function that unlocks the other doors when the driver door is opened within approximately 43 seconds of the ignition switch being turned off. By Shift to P: Function that unlocks all doors when the shift lever is moved to P from any position other than P with the ignition switch ON.	OFF, By Driver Door or By Shift to P	Main body ECU (Multiplex network body ECU)

System Diagram

SYSTEM DIAGRAM Communication Table Sender Receiver Signal Communication Method Power window regulator master switch assembly*1 ...

How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT HINT: Use the following procedure to troubleshoot the power door lock control system. *: Use the Techstream. PROCEDURE 1. VEHIC ...

Other materials:

Tailgate
The tailgate can be opened. Pull the handle Open the tailgate slowly The support cables will hold the tailgate horizontal. After closing the tailgate, try pulling it toward you to make sure it is securely locked. Removing the tailgate ■ Before removing the tailgate (vehicles with r ...

Transmitter ID1 Operation Stop (C2111/11-C2114/14)
DESCRIPTION The tire pressure warning valve and transmitters that are installed in the tire and wheel assemblies measure the tire pressure of each wheel. The measured values are transmitted to the tire pressure warning ECU and receiver in the vehicle as radio waves. The ECU compares the measu ...

Power Source Mode does not Change to ON (IG and ACC)
DESCRIPTION If any of the following operations are performed, the certification ECU (smart key ECU assembly) receives a signal, and changes the power source mode. With the electrical key transmitter sub-assembly in the cabin, the engine switch is pressed. When the battery of the e ...