DESCRIPTION
Refer to DTCs C1401 and C1402 (See page ).
DTC Code |
DTC Detection Condition |
Trouble Area |
---|---|---|
C1275 C1276 |
Stored only during test mode. |
|
C1413 C1414 |
One of the following conditions is met:
|
|
HINT:
WIRING DIAGRAM
Refer to DTCs C1405 and C1406 (See page ).
CAUTION / NOTICE / HINT
NOTICE:
PROCEDURE
1. |
CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
NG |
GO TO STEP 9 |
|
2. |
READ VALUE USING TECHSTREAM (FRONT SPEED SENSOR) |
NG |
GO TO STEP 5 |
|
3. |
PERFORM TEST MODE (SIGNAL CHECK) |
(a) Perform the signal check in the Test Mode Procedure (See page ).
OK:
All test mode DTCs are cleared.
NG |
GO TO STEP 5 |
|
4. |
RECONFIRM DTC |
(a) Clear the DTCs (See page ).
(b) Turn the ignition switch off.
(c) Start the engine.
(d) Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
(e) Check if the same DTC is output (See page ).
Result
Result |
Proceed to |
---|---|
DTCs C1413 and C1414 are not output |
A |
DTCs C1413 and/or C1414 are output |
B |
A |
USE SIMULATION METHOD TO CHECK |
B |
GO TO STEP 12 |
5. |
CHECK FRONT SPEED SENSOR INSTALLATION |
NG |
INSTALL FRONT SPEED SENSOR CORRECTLY |
|
6. |
INSPECT FRONT SPEED SENSOR TIP |
NG |
CLEAN OR REPLACE FRONT SPEED SENSOR |
|
7. |
INSPECT FRONT SPEED SENSOR ROTOR |
NG |
CLEAN OR REPLACE FRONT AXLE WITH ABS ROTOR BEARING ASSEMBLY |
|
8. |
INSPECT SKID CONTROL SENSOR WIRE |
NG |
REPLACE SKID CONTROL SENSOR WIRE |
|
9. |
CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR) |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
10. |
INSPECT SKID CONTROL ECU (FR+, FL+ TERMINAL) |
NG |
REPLACE MASTER CYLINDER SOLENOID |
|
11. |
RECONFIRM DTC |
(a) Clear the DTCs (See page ).
(b) Turn the ignition switch off.
(c) Start the engine.
(d) Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
(e) Check if the same DTC is output (See page ).
Result
Result |
Proceed to |
---|---|
DTCs C1413 and C1414 are not output |
A |
DTCs C1413 and/or C1414 are output |
B |
A |
USE SIMULATION METHOD TO CHECK |
|
12. |
REPLACE FRONT SPEED SENSOR |
|
13. |
RECONFIRM DTC |
(a) Clear the DTCs (See page ).
(b) Turn the ignition switch off.
(c) Start the engine.
(d) Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
(e) Check if the same DTC is output (See page ).
Result
Result |
Proceed to |
---|---|
DTCs C1413 and C1414 are not output |
A |
DTCs C1413 and/or C1414 are output |
B |
A |
END |
B |
REPLACE FRONT AXLE WITH ABS ROTOR BEARING ASSEMBLY |
Inspection
INSPECTION
PROCEDURE
1. INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
HINT:
The valve opening temperature is inscribed on the water inlet with thermostat
sub-assembly.
(a) Immerse the thermostat in the water, then heat the water gradually.
CAUTION:
Do not your hands into the wa ...
Rear Left Sensor Malfunction (C1AE6)
DESCRIPTION
The No. 1 ultrasonic sensor (rear corner sensor LH) is installed on the rear
bumper. The ECU detects obstacles based on signals received from the No. 1 ultrasonic
sensor (rear corner sensor LH). If the No. 1 ultrasonic sensor (rear corner sensor
LH) has an open circuit or other ma ...
Data List / Active Test
DATA LIST / ACTIVE TEST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference
values. Do not depend solely on these reference values when deciding whether a part
is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or s ...