INSTALLATION
PROCEDURE
1. INSTALL POWER STEERING LINK
(a) Insert the power steering link into the vehicle in the order shown in the illustration.
![]() |
Install in this Direction (1) |
![]() |
Install in this Direction (2) |
(b) Using SST, install the power steering link with the 2 bolts and 2 nuts. SST: 09961-01270 Torque: Specified tightening torque : 95 N·m {969 kgf·cm, 70 ft·lbf} NOTICE: While holding the nut in place, tighten the bolt. HINT:
|
|
2. CONNECT PRESSURE FEED TUBE ASSEMBLY
(a) Connect the return hose and slide the clip to secure it.
(b) Using a 17 mm union nut wrench, tighten the flare nut and connect the pressure feed tube. Torque: Specified tightening torque : 24 N·m {245 kgf·cm, 18 ft·lbf} NOTICE: Do not damage the pressure feed tube. HINT:
|
|
(c) Install the tube support brackets with the 2 bolts.
Torque:
28 N·m {286 kgf·cm, 21 ft·lbf}
3. INSTALL TIE ROD END SUB-ASSEMBLY LH
Click here
4. INSTALL TIE ROD END SUB-ASSEMBLY RH
HINT:
Use the same procedure described for the LH side.
5. PLACE FRONT WHEELS FACING STRAIGHT AHEAD
6. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT
(a) Align the matchmarks on the No. 2 steering intermediate shaft and power steering link. |
|
(b) Install the No. 2 steering intermediate shaft to the power steering link with bolt C.
Torque:
35 N·m {357 kgf·cm, 26 ft·lbf}
(c) Align the matchmarks on the steering intermediate shaft and steering sliding yoke. |
|
(d) Install the steering sliding yoke to the steering intermediate shaft and slide it upward.
(e) Align the matchmarks on the steering sliding yoke and No. 2 steering intermediate shaft.
(f) Install the steering sliding yoke to the No. 2 steering intermediate shaft with bolts A and B.
Torque:
35 N·m {357 kgf·cm, 26 ft·lbf}
7. INSTALL COOLER COMPRESSOR ASSEMBLY
(a) Install the 2 bolts and 2 nuts in the order shown in the illustration. Torque: 21 N·m {214 kgf·cm, 16 ft·lbf} |
|
(b) Install the suction hose sub-assembly with the bolt. Torque: 7.5 N·m {76 kgf·cm, 66 in·lbf} |
|
(c) Install the fan and generator V belt.
Click here
8. INSTALL AUTOMATIC TRANSMISSION OIL COOLER TUBE (for Automatic Transmission)
(a) Install the automatic transmission oil cooler tube and clamp with the bolt. Torque: 5.5 N·m {56 kgf·cm, 49 in·lbf} |
|
9. INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)
Click here
10. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
Torque:
30 N·m {306 kgf·cm, 22 ft·lbf}
11. INSTALL NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Off Road Package)
Torque:
30 N·m {306 kgf·cm, 22 ft·lbf}
12. INSTALL FRONT UPPER FENDER APRON SEAL
Click here
13. INSTALL FRONT WHEELS
Torque:
113 N·m {1152 kgf·cm, 83 ft·lbf}
14. INSPECT STEERING WHEEL CENTER POINT
15. ADD POWER STEERING FLUID
16. BLEED POWER STEERING FLUID
Click here
17. INSPECT FOR POWER STEERING FLUID LEAK
18. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
Click here
Room Light Assembly
Components
COMPONENTS
ILLUSTRATION
Removal
REMOVAL
PROCEDURE
1. REMOVE NO. 1 ROOM LIGHT ASSEMBLY
(a) Using a screwdriver with its tip wrapped in protective tape, disengage
the 4 claws to remove the No. 1 room light lens.
Text in Illustration
*a
...
Reassembly
REASSEMBLY
CAUTION / NOTICE / HINT
CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
PROCEDURE
1. INSTALL SEPARATE TYPE REAR SEATBACK COVER
(a) Using hog ring pliers, install the separate type rear seatback cover
with 2 new hog rings.
Text in Il ...
Acceleration Sensor Power Supply Voltage Malfunction (C1381)
DESCRIPTION
The skid control ECU (brake actuator assembly) receives signals from the yaw
rate and acceleration sensor (airbag sensor assembly) via the CAN communication
system.
The airbag sensor assembly has a built-in acceleration sensor and detects the
vehicle condition.
If there is troub ...