DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Sliding Roof or Main Body / Data List.
(e) Read the Data List according to the display on the Techstream.
Sliding Roof
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
---|---|---|---|
Open Switch |
OPEN switch signal/ON or OFF |
ON: OPEN switch pressed OFF: OPEN switch not pressed |
- |
Close Switch |
CLOSE switch signal/ON or OFF |
ON: CLOSE switch pressed OFF: CLOSE switch not pressed |
- |
Up Switch |
UP switch signal/ON or OFF |
ON: UP switch pressed OFF: UP switch not pressed |
- |
Down Switch |
DOWN switch signal/ON or OFF |
ON: DOWN switch pressed OFF: DOWN switch not pressed |
- |
Front SW Auto Operation |
Sliding roof auto function/ON or OFF |
Customization status displayed |
- |
Hall IC1 Pulse |
Hall IC1 pulse output/Lo or Hi |
Lo and Hi repeat during motor operation |
Lo: Hall IC1 output is low Hi: Hall IC1 output is high |
Hall IC1 Status |
Status of Hall IC1/Normal or Error |
Normal: Hall IC1 normal Error: Hall IC1 not normal |
- |
Hall IC2 Pulse |
Hall IC2 pulse output/Lo or Hi |
Lo and Hi repeat during motor operation |
Lo: Hall IC2 output is low Hi: Hall IC2 output is high |
Hall IC2 Status |
Status of Hall IC2/Normal or Error |
Normal: Hall IC2 normal Error: Hall IC2 not normal |
- |
Ignition (Direct Signal) |
Ignition switch signal/ON or OFF |
ON: Ignition switch ON OFF: Ignition switch off |
- |
Ignition (MPX) |
Ignition switch signal (LIN signal)/ON or OFF |
ON: Ignition switch ON OFF: Ignition switch off |
- |
Door Courtesy |
Driver door courtesy light switch signal/ON or OFF |
ON: Driver door open OFF: Driver door closed |
- |
Door Handle Lock Button*1 |
Smart key lock button switch signal/ON or OFF |
ON: Smart key lock button switch pressed OFF: Smart key lock button switch not pressed |
- |
Door Key Close Operation |
Key-linked sliding roof close signal/ON or OFF |
ON: Turn and hold the driver door key cylinder to lock position OFF: Driver door key cylinder not turned |
- |
Door Key Open Operation |
Key-linked sliding roof open signal/ON or OFF |
ON: Turn and hold the driver door key cylinder to unlock position OFF: Driver door key cylinder not turned |
- |
Wireless Close Operation |
Wireless transmitter-linked sliding roof close signal/ON or OFF |
ON: Press and hold the transmitter LOCK switch OFF: Transmitter LOCK switch not pressed |
- |
Wireless Open Operation |
Wireless transmitter-linked sliding roof open signal/ON or OFF |
ON: Press and hold the transmitter UNLOCK switch OFF: Transmitter UNLOCK switch not pressed |
- |
Key Off Permission |
Key-off sliding roof operation permit signal/ON or OFF |
ON: Front doors are not opened within 43 seconds after ignition switch turned off OFF: Any status except "ON" status |
- |
Door Key Related Operation |
Key-linked sliding roof open function operating direction/Slide or Tilt |
Customization status displayed |
- |
Wireless Key Rel Operation |
Wireless transmitter-linked sliding roof open function operating direction/Slide or Tilt |
Customization status displayed |
- |
Open Switch Failure(Past) |
Open switch failure signal (Past)/ON or OFF |
ON: Sliding roof open switch failure signal (Past) OFF: No sliding roof open switch failure signal (Past) |
- |
Close Switch Failure(Past) |
Close switch failure signal (Past)/ON or OFF |
ON: Sliding roof close switch failure signal (Past) OFF: No sliding roof close switch failure signal (Past) |
- |
Up Switch Failure(Past) |
Up switch failure signal (Past)/ON or OFF |
ON: Sliding roof tilt up switch failure signal (Past) OFF: No sliding roof tilt up switch failure signal (Past) |
- |
Down Switch Failure(Past) |
Down switch failure signal (Past)/ON or OFF |
ON: Sliding roof tilt down switch failure signal (Past) OFF: No sliding roof tilt down switch failure signal (Past) |
- |
Open Switch Failure(Current) |
Open switch failure signal (Current)/ON or OFF |
ON: Sliding roof open switch failure signal (Current) OFF: No sliding roof open switch failure signal (Current) |
- |
Close Switch Failure(Current) |
Close switch failure signal (Current)/ON or OFF |
ON: Sliding roof close switch failure signal (Current) OFF: No sliding roof close switch failure signal (Current) |
- |
Up Switch Failure(Current) |
Up switch failure signal (Current)/ON or OFF |
ON: Sliding roof tilt up switch failure signal (Current) OFF: No sliding roof tilt up switch failure signal (Current) |
- |
Down Switch Failure(Current) |
Down switch failure signal (Current)/ON or OFF |
ON: Sliding roof tilt down switch failure signal (Current) OFF: No sliding roof tilt down switch failure signal (Current) |
- |
Number of Trouble Codes |
Number of DTCs / Min.: 0, Max.: 255 |
Number of stored DTCs |
- |
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
---|---|---|---|
Slide Roof Open Warning |
Sliding roof open warning/ON or OFF |
Customization status displayed |
- |
2. ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Sliding Roof / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Sliding Roof
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
---|---|---|---|
Slide Roof |
Operate sliding roof motor |
OFF / Opn/Dwn / Clos/Up |
- |
Camper information
This information has been prepared in accordance with regulation issued by
the National Highway Traffic Safety Administration of the U.S. Department of Transportation.
It provides the purchasers and/or prospective purchasers of Toyota vehicles with
information on truck-camper loading. Your Toy ...
GPS Mark is not Displayed
PROCEDURE
1.
CHECK CABIN
(a) Check the cabin for any object that might interrupt radio reception or additional
devices which use radio waves on the instrument panel. If such an object exists,
remove it and check if the GPS mark reappears.
HINT:
The GPS uses ex ...
ECM Communication Circuit Malfunction (C1203)
DESCRIPTION
The circuit is used to send TRAC and VSC control information from the skid control
ECU (brake actuator assembly) to the ECM, and engine control information from the
ECM to the skid control ECU (brake actuator assembly) through the CAN communication
system.
for 4WD or w/ Rear Diff ...