Toyota Tacoma (2015-2018) Service Manual: Front Speed Sensor RH Performance (C1409,C1410)

Toyota Tacoma (2015-2018) Service Manual / Brake Control / Dynamic Control Systems / Vehicle Stability Control System(for Hydraulic Brake Booster) / Front Speed Sensor RH Performance (C1409,C1410)

DESCRIPTION

Refer to DTCs C1401 and C1402 (See page ).

DTC Code	DTC Detection Condition	Trouble Area
C1409 C1410	One of the following conditions is met: When the vehicle is driven in reverse at a speed of 3 km/h (2 mph) or more and 3 of the wheel sensors detect the reverse signal, the other sensor detects a high frequency pulse 75 times while the ignition switch is ON. At a vehicle speed of 10 km/h (6 mph) or more, the vehicle speed sensor output drops by 50% for 5 seconds. The lowest wheel speed is 10 km/h (6 mph) or more and the difference between the highest and lowest wheel speed values is 2 km/h (1 mph) or less for 15 seconds. At a vehicle speed of 30 km/h (19 mph) or more, one wheel direction is different from the other 3 wheels for 1 second. At a vehicle speed of 100 km/h (62 mph), a reverse signal is output for 1 second or more. At a vehicle speed of 30 km/h (19 mph) or more, the rotation direction of one of the wheels is not detected normally and the rotation direction of the other 3 wheels is not the same for 1 second.	Front speed sensor RH/LH

DTC Code

DTC Detection Condition

Trouble Area

C1409

C1410

One of the following conditions is met:

When the vehicle is driven in reverse at a speed of 3 km/h (2 mph) or more and 3 of the wheel sensors detect the reverse signal, the other sensor detects a high frequency pulse 75 times while the ignition switch is ON.
At a vehicle speed of 10 km/h (6 mph) or more, the vehicle speed sensor output drops by 50% for 5 seconds.
The lowest wheel speed is 10 km/h (6 mph) or more and the difference between the highest and lowest wheel speed values is 2 km/h (1 mph) or less for 15 seconds.
At a vehicle speed of 30 km/h (19 mph) or more, one wheel direction is different from the other 3 wheels for 1 second.
At a vehicle speed of 100 km/h (62 mph), a reverse signal is output for 1 second or more.
At a vehicle speed of 30 km/h (19 mph) or more, the rotation direction of one of the wheels is not detected normally and the rotation direction of the other 3 wheels is not the same for 1 second.

Front speed sensor RH/LH

HINT:

DTC C1409 is for the front speed sensor RH.
DTC C1410 is for the front speed sensor LH.

CAUTION / NOTICE / HINT

NOTICE:

Check the speed sensor signal after replacement (See page PROCEDURE ).

PROCEDURE

1.	REPLACE FRONT SPEED SENSOR

(a) Replace the front speed sensor (See page ).

END

Open or Short in Rear Speed Sensor RH Circuit (C1407,C1408)

DESCRIPTION Refer to DTCs C1401 and C1402 (See page ). DTC Code DTC Detection Condition Trouble Area C1407 C1408 Either condition is ...

Rear Speed Sensor RH Performance (C1411,C1412)

DESCRIPTION Refer to DTCs C1401 and C1402 (See page ). DTC Code DTC Detection Condition Trouble Area C1411 C1412 One of the following ...

Other materials:

Reassembly
REASSEMBLY PROCEDURE 1. INSTALL CONSOLE COMPARTMENT DOOR HINGE SUB-ASSEMBLY (a) Engage the 2 guides to install the console compartment door hinge sub-assembly. (b) Install the 4 screws. (c) Engage the 2 guides and 4 claws ...

Removal
REMOVAL CAUTION / NOTICE / HINT PROCEDURE 1. PRECAUTION CAUTION: Be sure to read Precaution thoroughly before servicing (See page ). NOTICE: After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore ...

ABS Warning Light Remains ON
DESCRIPTION The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication. If any of the following is detected, the ABS warning light remains on: The skid control ECU (brake actuator assembly) connectors are disconnected from the ...