Toyota Tacoma 2015-2018 Service Manual: Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
Air Conditioning System|
DTC Code |
Detection Item |
Memory |
See page |
|---|---|---|---|
|
B1411/11 |
Room Temperature Sensor Circuit |
Memorized (4 seconds or more) |
|
|
B1412/12 |
Ambient Temperature Sensor Circuit |
Memorized (4 seconds or more) |
|
|
B1413/13 |
Evaporator Temperature Sensor Circuit |
Memorized (4 seconds or more) |
|
|
B1422/22 |
Compressor Lock Sensor Circuit |
Memorized (3 seconds or more) |
|
|
B1423/23 |
Pressure Sensor Circuit |
- |
|
|
B1431/31 |
Air Mix Damper Position Sensor Circuit (Passenger Side) |
Memorized (4 seconds or more) |
|
|
B1432/32 |
Air Inlet Damper Position Sensor Circuit |
Memorized (4 seconds or more) |
|
|
B1433/33 |
Air Outlet Damper Position Sensor Circuit |
Memorized (4 seconds or more) |
|
|
B1436/36 |
Air Mix Damper Position Sensor Circuit (Driver Side) |
Memorized (4 seconds or more) |
|
|
B1441/41 |
Air Mix Damper Control Servo Motor Circuit (Passenger Side) |
Memorized (16 seconds or more) |
|
|
B1442/42 |
Air Inlet Damper Control Servo Motor Circuit |
Memorized (16 seconds or more) |
|
|
B1443/43 |
Air Outlet Damper Control Servo Motor Circuit |
Memorized (16 seconds or more) |
|
|
B1446/46 |
Air Mix Damper Control Servo Motor Circuit (Driver Side) |
Memorized (16 seconds or more) |
|
|
B14B2 |
Lost Communication with Front Panel LIN |
Memorized (10 seconds or more) |
|
|
U0100 |
Lost Communication with ECM |
- |
|
|
U0142 |
Lost Communication with Main Body ECU |
- |
|
|
U0155 |
Lost Communication with Combination Meter |
- |
|
.gif)
Data List / Active Test
DATA LIST / ACTIVE TEST
1. DATA LIST
Using the Techstream to read the Data List allows the values or states of switches,
sensors, actuators and other items to be read without removing any parts. T ...
Dtc Check / Clear
DTC CHECK / CLEAR
1. DTC CHECK USING TECHSTREAM
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electri ...
Other materials:
Terminals Of Ecu
TERMINALS OF ECU
1. CHECK DRIVER SIDE JUNCTION BLOCK AND MAIN BODY ECU (MULTIPLEX NETWORK BODY
ECU)
(a) Disconnect the MB main body ECU (multiplex network body ECU) connectors.
(b) Measure the voltage and resistance according to the value(s) in the table
below.
HINT:
Measure the values on ...
Torque Converter And Drive Plate
Inspection
INSPECTION
PROCEDURE
1. INSPECT TORQUE CONVERTER ASSEMBLY
(a) Inspect the one-way clutch.
(1) Press on the spline of the stator with a finger and rotate the spline. Check
that the spline rotates smoothly when turned clockwise and rotates with difficulty
when turned counterclock ...
Headlight Relay
Inspection
INSPECTION
PROCEDURE
1. INSPECT HEADLIGHT RELAY
(a) Check the resistance.
(1) Using an ohmmeter, measure the resistance between the terminals.
Standard:
Tester Connection
Specified Condition
3-5
10 kΩ or higher
...