Toyota Tacoma (2015-2018) Service Manual: Road Test

Toyota Tacoma (2015-2018) Service Manual / Ac60e Automatic Transmission / Transaxle / Automatic Transmission System(for 2gr-fks) / Road Test

ROAD TEST

1. PROBLEM SYMPTOM CONFIRMATION

(a) Based on the result of the customer problem analysis, try to reproduce the symptoms. If the problem is that the transmission does not shift up or down, or that the shift point is too high or too low, conduct the following road test referring to the automatic shift schedule and attempt to duplicate the problem symptoms.

2. ROAD TEST

(a) Perform a road test.

CAUTION:

Check for safety before performing any tests.

NOTICE:

Be sure to inspect and adjust the engine before performing these tests.
Perform the road test with the engine coolant temperature is 70°C (158°F) or higher and the ATF temperature between 40 and 110°C (104 and 230°F).
Perform these tests with the air conditioning and cruise control off.

Inspection	Procedure
Transmission Control Switch Test	With the vehicle stationary and the shift lever in D, move the shift lever to S and return it to D. Check that the meter display changes from D to the appropriate S range and then back again.
S Position Test	With the vehicle stationary and the shift lever in S, move the shift lever to "+" and "-". Check that the meter display changes between S ranges properly.
D Position Shift Test	While driving the vehicle normally, check that the transmission shifts up and down through each gear properly.
Lock-up Function	While driving on a level surface at a constant speed in the lock-up range with the shift lever in D, lightly depress the accelerator pedal and check that the engine speed does not change abruptly.
P Position Test	Stop the vehicle on an incline (approximately 5° or more). Then move the shift lever to P and release the parking brake. Check that the parking lock pawl holds the vehicle in place.
Abnormal Noise and Vibration	Check for abnormal noise and vibration while driving the vehicle forward and backward, and during shift operations.
Fluid Leakage	After performing all other road test inspections, check for fluid leakage.

HINT:

When checking for DTCs after a repair, drive the vehicle according to the monitor drive pattern (See page (b) Shift schedule confirmation ).

(b) Shift schedule confirmation

(1) Connect the Techstream to the DLC3.

(2) Turn the ignition switch to ON.

(3) Turn the Techstream on.

(4) Enter the following menus: Powertrain / Transmission / Data List / Vehicle Speed, Accel Position from EFI and Shift Status.

(5) Check that the "Shift Status" changes in accordance with the "Vehicle Speed" as shown in the following table.

Shift Schedule Chart

Accelerator Position	6%
Shift Status (Shift Lever in D)	1st to 2nd	2nd to 3rd	3rd to 4th	4th to 5th	5th to 6th
Vehicle Speed	10 to 15 km/h (6 to 9 mph)	20 to 30 km/h (12 to 19 mph)	30 to 40 km/h (19 to 25 mph)	45 to 55 km/h (28 to 34 mph)	60 to 75 km/h (37 to 47 mph)

Accelerator Position

Shift Status

(Shift Lever in D)

1st to 2nd

2nd to 3rd

3rd to 4th

4th to 5th

5th to 6th

Vehicle Speed

10 to 15 km/h

(6 to 9 mph)

20 to 30 km/h

(12 to 19 mph)

30 to 40 km/h

(19 to 25 mph)

45 to 55 km/h

(28 to 34 mph)

60 to 75 km/h

(37 to 47 mph)

NOTICE:

All vehicle speeds indicated in the above table are actual values. Therefore, if checking a shift point with a chassis dynamometer, keep in mind that there is a margin of error in the chassis dynamometer indication.
If checking a shift point against the vehicle speed indicated on the speedometer, remember to consider the speedometer correction rate and margin of error in the Techstream indication.

(1) Connect the Techstream to the DLC3.

(2) Turn the ignition switch to ON.

(3) Turn the Techstream on.

(4) Enter the following menus: Powertrain / Transmission / Data List / Vehicle Speed, Engine Speed, Accel Position from EFI, NT Sensor Speed, A/T Oil Temperature 1, Lock Up Status and Shift Status.

(5) When the following conditions are met, check that the difference between "Engine Speed" and "NT Sensor Speed" is 50 rpm or less.

Lock-up Schedule

Accel Position from EFI	6%
Vehicle Speed	80 km/h (50 mph) or more
Shift Status	6th gear
Lock Up Status	ON

HINT:

Lock-up prohibition conditions:

A/T oil temperature is below 40°C (104°F)
Engine coolant temperature is below 70°C (158°F)
Shift range between "1" (S1 range) and "3" (S3 range)
Accelerator pedal is fully released
Stop light switch signal is on

(d) Manual down-shift permission speed

(1) Manual down-shift is permitted for each shift status when the vehicle speed is below the corresponding range shown in the following table.

Manual Down-shift Permission Speed Chart

Shift Status (Shift Lever in S)	S6 to S5	S5 to S4	S4 to S3	S3 to S2	S2 to S1
Vehicle Speed	280 to 305 km/h (174 to 190 mph)	190 to 210 km/h (118 to 130 mph)	125 to 145 km/h (78 to 90 mph)	90 to 100 km/h (56 to 62 mph)	40 to 50 km/h (25 to 31 mph)

Shift Status

(Shift Lever in S)

S6 to S5

S5 to S4

S4 to S3

S3 to S2

S2 to S1

Vehicle Speed

280 to 305 km/h

(174 to 190 mph)

190 to 210 km/h

(118 to 130 mph)

125 to 145 km/h

(78 to 90 mph)

90 to 100 km/h

(56 to 62 mph)

40 to 50 km/h

(25 to 31 mph)

(e) Shift schedule when accelerator pedal is fully depressed

Shift Schedule Chart

Accelerator Pedal	Fully Depressed
Shift Status (Shift Lever in D)	1st to 2nd	2nd to 3rd	3rd to 4th	4th to 5th	5th to 6th
Vehicle Speed	45 to 55 km/h (28 to 34 mph)	90 to 105 km/h (56 to 65 mph)	130 to 150 km/h (81 to 93 mph)	210 to 230 km/h (130 to 143 mph)	305 to 330 km/h (190 to 205 mph)

Accelerator Pedal

Fully Depressed

Shift Status

(Shift Lever in D)

1st to 2nd

2nd to 3rd

3rd to 4th

4th to 5th

5th to 6th

Vehicle Speed

45 to 55 km/h

(28 to 34 mph)

90 to 105 km/h

(56 to 65 mph)

130 to 150 km/h

(81 to 93 mph)

210 to 230 km/h

(130 to 143 mph)

305 to 330 km/h

(190 to 205 mph)

Mechanical System Tests

MECHANICAL SYSTEM TESTS 1. STALL SPEED TEST HINT: This test is to check the overall performance of the engine and transmission. CAUTION: This test should be done on a paved surface (a sur ...

Initialization

INITIALIZATION 1. RESET MEMORY NOTICE: Perform Reset Memory (AT initialization) when replacing the automatic transmission assembly, transmission valve body assembly or any of the shift ...

Other materials:

LVDS Signal Malfunction (from Extension Module) (B1532)
DESCRIPTION The stereo component tuner assembly and the radio and display receiver assembly are connected by an LVDS communication line. This DTC is stored when an LVDS communication error occurs between the stereo component tuner assembly and the radio and display receiver assembly. ...

Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) (C1277,...,C1416)
DESCRIPTION Refer to DTCs C1401 and C1402 (See page ). DTC Code DTC Detection Condition Trouble Area C1277 C1278 Stored only during test mode. Rear speed sensor RH/LH Rear speed sensor rotor RH/LH (Rear ax ...

System Diagram
SYSTEM DIAGRAM Communication Table Sender Receiver Signal Line *1: for Vacuum Brake Booster *2: for Hydraulic Brake Booster Millimeter Wave Radar Sensor Assembly Forward Recognition Camera ...