Toyota Tacoma (2015-2018) Service Manual: Reassembly

Toyota Tacoma (2015-2018) Service Manual / Engine Hood / Door / Hood / Reassembly

REASSEMBLY

CAUTION / NOTICE / HINT

NOTICE:

When installing the hood bulge protector, heat the hood bulge surface using the infrared light.
Do not heat the hood bulge excessively.

Item

Temperature

Hood Bulge

20 to 30°C (68 to 86°F)

Item	Temperature
Hood Bulge	20 to 30°C (68 to 86°F)

PROCEDURE

1. INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY

(a) Tie the string that was passed thorough the engine compartment room to the end of the hood lock control cable assembly as shown in the illustration.

(b) Pass the hood lock control cable assembly into the engine compartment.

(d) Remove the string from the hood lock control cable assembly.

2. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

(a) Connect the hood lock control cable assembly to install the hood lock control lever sub-assembly.

(b) Engage the claw and 3 guides to install the hood lock control lever sub-assembly.

3. INSTALL HOOD STAY HOLDER

(a) Engage the 2 claws to install the hood stay holder.

4. INSTALL HOOD SUPPORT

(a) Install the grommet.

(b) Install the hood support.

5. INSTALL HOOD LOCK ASSEMBLY

6. INSTALL RADIATOR GRILLE

7. CONNECT WASHER HOSE ASSEMBLY

(a) Engage the 4 claws to install the 4 clamps.

(b) Engage the 4 clamps to connect the washer hose assembly.

8. INSTALL WASHER NOZZLE SUB-ASSEMBLY

9. INSTALL HOOD TO RADIATOR SUPPORT SEAL

(a) Install the 7 clips and hood to radiator support seal.

10. INSTALL NO. 1 HOOD BULGE PROTECTOR (w/ Hood Bulge)

(a) Install the No. 1 hood bulge protector.

11. INSTALL HOOD AIR INTAKE GUIDE (w/ Hood Bulge)

(a) Engage the 5 guides to install the hood air intake guide.

(b) Install the 4 screws.

12. INSTALL NO. 2 HOOD BULGE PROTECTOR (w/ Hood Bulge)

(a) Install the No. 2 hood bulge protector.

13. INSTALL HOOD BULGE ASSEMBLY (w/ Hood Bulge)

(a) Engage the clip from the back side of the hood panel to install the hood bulge assembly together with the air intake guide.

(b) Install the 4 nuts.

Disassembly

DISASSEMBLY PROCEDURE 1. REMOVE HOOD BULGE ASSEMBLY (w/ Hood Bulge) (a) Remove the 4 nuts. (b) Disengage the clip from back side of the hood pa ...

Rear Door(for Access Cab)

Adjustment ADJUSTMENT CAUTION / NOTICE / HINT HINT: Use the same procedures for both the LH and RH sides. The procedure described below is for the LH side. Centering bolts are us ...

Other materials:

Evaporator Temperature Sensor Circuit (B1413/13)
DESCRIPTION The cooler thermistor sensor (evaporator temperature sensor) is installed on the evaporator in the air conditioner unit to detect the temperature of the cooled air that has passed through the evaporator and is used to control the air conditioning. It sends signals to the air condi ...

Inspection
INSPECTION PROCEDURE 1. INSPECT FUEL INJECTOR ASSEMBLY (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Condition Specified Condition 1 - 2 20°C (68°F) 11.6 ...

Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE REAR BUMPER HOLE COVER (a) Disengage the 2 clips to remove the rear bumper hole cover. 2. REMOVE REAR BUMPER PAD SUB-ASSEMBLY (a) Separate the 2 license plate light assemblies as shown in the illustr ...