Toyota Tacoma manuals

Toyota Tacoma 2015-2018 Service Manual: Rear Door(for Double Cab)

Components

COMPONENTS

ILLUSTRATION

ILLUSTRATION

ILLUSTRATION

ILLUSTRATION

ILLUSTRATION

ILLUSTRATION

ILLUSTRATION

ILLUSTRATION

ILLUSTRATION

Adjustment

Adjustment

ADJUSTMENT

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedures for both the LH and RH sides.
  • The procedure described below is for the LH side.
  • Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments. Text in Illustration

    *1

    Centering Bolt

    *2

    Standard Bolt

  • A bolt without a torque specification is shown in the standard bolt chart (See page ).

PROCEDURE

1. INSPECT REAR DOOR PANEL SUB-ASSEMBLY

(a) Check that the clearance measurements of areas "A" through "F" are within each standard range.

Standard Clearance:

Area

Measurement

Area

Measurement

A

3.5 to 6.5 mm (0.138 to 0.256 in.)

B

3.3 to 6.3 mm (0.130 to 0.248 in.)

C

0.2 to 3.2 mm (0.008 to 0.126 in.)

D

2.9 to 5.9 mm (0.114 to 0.232 in.)

E

3.4 to 6.4 mm (0.134 to 0.252 in.)

F

0.5 to 3.5 mm (0.020 to 0.138 in.)

2. ADJUST REAR DOOR PANEL SUB-ASSEMBLY

(a) Adjust the door horizontally and vertical by loosening the 4 body side hinge bolts.

(b) Tighten the 4 body side hinge bolts after the adjustment.

Torque:

26 N·m {265 kgf·cm, 19 ft·lbf}

NOTICE:

Adjust the door fitting after the bolts were replaced with new ones.

(c) Adjust the door horizontally and vertical by loosening the 4 door side hinge bolts.

(d) Tighten the 4 door side hinge bolts after the adjustment.

Torque:

26 N·m {265 kgf·cm, 19 ft·lbf}

NOTICE:

Adjust the door fitting after the bolts were replaced with new ones.

(e) Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.

(f) Using a brass bar and a hammer, hit the striker to adjust its position.

(g) Using a T40 "TORX" socket wrench, tighten the 2 striker mounting screws after adjustment.

Torque:

23 N·m {235 kgf·cm, 17 ft·lbf}

Rear Door(for Access Cab)
Adjustment ADJUSTMENT CAUTION / NOTICE / HINT HINT: Use the same procedures for both the LH and RH sides. The procedure described below is for the LH side. Centering bolts are us ...

Tail Gate
...

Other materials:

Adjustment
ADJUSTMENT PROCEDURE 1. PREPARE VEHICLE FOR HEADLIGHT AIM ADJUSTMENT (a) Prepare the vehicle: Ensure that there is no damage or deformation to the body around the headlights. Fill the fuel tank. Make sure that the oil is filled to the specified level. Make sure that the co ...

Terminals Of Ecu
TERMINALS OF ECU 1. CHECK DRIVER SIDE JUNCTION BLOCK AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (a) Disconnect the MB main body ECU (multiplex network body ECU) connectors. (b) Measure the voltage and resistance according to the value(s) in the table below. HINT: Measure the values on ...

Sound of Portable Player cannot be Heard from Speakers or Sound is Low
PROCEDURE 1. CHECK PORTABLE PLAYER SETTINGS (a) Check the portable player settings. (1) Check that the volume is not set to "0". (2) Check that the mute is off. (b) Check that the sound of the portable player can be heard from the speakers. OK: Sound ...

© 2011-2022 Copyright www.ttguide.net