Toyota Tacoma (2015-2018) Service Manual: Rear Center Seat Outer Belt Assembly(for Double Cab)

Toyota Tacoma (2015-2018) Service Manual / Seat Belt / Rear Center Seat Outer Belt Assembly(for Double Cab)

Components

COMPONENTS

ILLUSTRATION

Removal

REMOVAL

PROCEDURE

1. REMOVE REAR SEATBACK HINGE COVER

2. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY

3. REMOVE SEAT BELT ANCHOR COVER CAP

4. REMOVE REAR SEAT SHOULDER BELT COVER

5. REMOVE CENTER SEATBACK PAD

(a) Remove the center seatback pad.

6. REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY

(a) Remove the bolt to disconnect the floor anchor of the rear center seat outer belt assembly and rear seat inner belt assembly.

(b) Insert the belt through the hole into the rear seatback frame.

(d) Disengage the 2 guides to remove the rear center seat outer belt assembly.

Installation

INSTALLATION

PROCEDURE

1. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY

(a) Before installing the rear center seat outer belt assembly, check the ELR function.

Text in Illustration

*a	Unlock
*b	Lock
*c	45°

(1) When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.

NOTICE:

Do not disassemble the retractor.

(b) Engage the 2 guides to install the rear center seat outer belt assembly with the bolt.

Torque:

42 N·m {428 kgf·cm, 31 ft·lbf}

(d) Connect the rear seat inner belt assembly and rear center seat outer belt assembly by installing the floor anchor with the bolt.

Text in Illustration

*a	Protruding Part
*b	40°

Torque:

42 N·m {428 kgf·cm, 31 ft·lbf}

NOTICE:

Make sure that the rear seat inner belt assembly and rear center seat outer belt assembly is oriented in the correct direction when installing.
Do not allow the anchor part of the rear seat inner belt assembly and rear center seat outer belt assembly to overlap the protruding part of the floor panel.

2. INSTALL CENTER SEATBACK PAD

(a) Install a new center seatback pad.

3. INSTALL REAR SEAT SHOULDER BELT COVER

4. INSTALL SEAT BELT ANCHOR COVER CAP

5. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY

6. INSTALL REAR SEATBACK HINGE COVER

Rear Seat Inner Belt Assembly(for Access Cab)

Disposal

DISPOSAL CAUTION / NOTICE / HINT CAUTION: Before performing pre-disposal deployment of any SRS component, review and closely follow all applicable environmental and hazardous material regulations ...

Rear Seat Inner Belt Assembly(for Access Cab)

Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY (a) Open the 2 anchor covers. (b) Loosen the 2 bolts to remove the 2 ...

Other materials:

System Description
SYSTEM DESCRIPTION LANE DEPARTURE ALERT SYSTEM DESCRIPTION (a) The lane departure alert system is a system which uses the forward recognition camera to recognize and determine the lane and the position of the vehicle when the vehicle is being driven on highways and other roads with white (yell ...

Installation
INSTALLATION PROCEDURE 1. INSTALL FRONT CONSOLE BOX (for Automatic Transmission) (a) When installing a new front console box: Text in Illustration *a Runner Portion *b Cut Off (1) Usin ...

Monitor Drive Pattern
MONITOR DRIVE PATTERN 1. TEST MONITOR DRIVE PATTERN FOR ECT CAUTION: Perform this drive pattern on a level surface and strictly observe the posted speed limits and traffic laws while driving. HINT: Performing this drive pattern is one method to simulate the ECM (ECT) malfunction detection c ...