ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT SPEEDOMETER
(a) Check speedometer operation.
NOTICE:
(1) Before starting the following inspection, check if the Brake Control System outputs the DTCs.
(2) Check the values by referring to the table below.
ABS/VSC/TRAC
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
---|---|---|---|
Vehicle Speed |
Maximum wheel speed sensor reading/ Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
Techstream Indication (mph) |
Acceptable Range (mph) |
---|---|
20 |
19.2 to 21.7 |
40 |
39.4 to 42.2 |
60 |
59.8 to 62.6 |
80 |
80.0 to 83.2 |
100 |
100.5 to 103.7 |
120 |
120.9 to 124.1 |
140 |
141.3 to 144.5 |
Techstream Indication (km/h) |
Acceptable Range (km/h) |
---|---|
20 |
18.4 to 22.4 |
40 |
38.6 to 43.1 |
60 |
59.0 to 63.5 |
80 |
79.1 to 84.1 |
100 |
99.6 to 104.6 |
120 |
120.0 to 125.0 |
140 |
140.4 to 145.4 |
160 |
160.8 to 165.8 |
180 |
181.2 to 186.2 |
200 |
201.6 to 206.6 |
220 |
222.0 to 227.0 |
2. INSPECT TACHOMETER
(a) Check the operation.
(1) Connect the Techstream, and start the engine.
(2) Compare the test results with the tachometer indications.
Reference
Techstream Indication (rpm) |
Acceptable Range (rpm) Data in ( ) is for Reference |
---|---|
700 |
630 to 770 |
1000 |
(900 to 1100) |
2000 |
(1850 to 2150) |
3000 |
2800 to 3200 |
4000 |
(3800 to 4200) |
5000 |
4800 to 5200 |
6000 |
(5750 to 6250) |
7000 |
6700 to 7300 |
8000 |
(7700 to 8300) |
3. CHECK LED ILLUMINATION (LED CHECK)
Warning or Indicator Light |
Specified Condition |
---|---|
Brake warning light |
Warning or indicator light comes on for about 3 seconds after turning the ignition switch to ON. |
VSC OFF indicator light |
|
Slip indicator light |
|
ABS warning light |
|
Tire pressure warning light*1 |
|
AUTO LSD indicator light |
|
PCS warning light*2 |
|
TRAC OFF indicator light |
|
Master warning light |
|
SRS warning light |
Warning light comes on for about 6 seconds after turning the ignition switch to ON. |
MIL (Check engine warning light) |
Warning light comes on when turning the ignition switch to ON. |
Freeze Frame Data
FREEZE FRAME DATA
CHECK FREEZE FRAME DATA
HINT:
The ECU records vehicle and driving condition information as freeze frame data
the moment a DTC is stored.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: P ...
Installation
INSTALLATION
PROCEDURE
1. INSTALL FORWARD RECOGNITION CAMERA
NOTICE:
When replacing the forward recognition camera, replace it with a new
one.
Do not touch the camera lens. If the camera lens has been touched, do
not use the forward recognition camera.
If the forward reco ...
Air conditioning filter
The air conditioning filter must be changed regularly to maintain air conditioning
efficiency.
■ Removal method
Turn the engine switch to the LOCK
position.
Open the glove box.
Slide off the damper.
Push in each side of the glove box to disconnect the claws.
Open the filter ...