Toyota Tacoma (2015-2018) Service Manual: How To Proceed With Troubleshooting

Toyota Tacoma (2015-2018) Service Manual / Window / Glass / Power Window Control System(w/ Jam Protection Function) / How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT

HINT:

Use the following procedure to troubleshoot the power window control system.
*: Use the Techstream.

PROCEDURE

1.	VEHICLE BROUGHT TO WORKSHOP

2.	CUSTOMER PROBLEM ANALYSIS

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

The following 5 items are important points in the problem analysis:

What	Vehicle model, system name
When	Date, time, occurrence frequency
Where	Road conditions
Under what conditions?	Driving conditions, weather conditions
How did it happen?	Problem symptoms

PRE-CHECK

(a) Measure the battery voltage.

Standard voltage:

11 to 14 V

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

(b) Check the fuses and relays.

(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.

4.	INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

(a) Use the Techstream to check if the LIN communication system is functioning normally.

Click here

Result	Proceed to
No DTCs output	A
DTCs output	B

GO TO LIN COMMUNICATION SYSTEM

5.	CHECK LIN COMMUNICATION SYSTEM POWER WINDOW REGULATOR MASTER SWITCH

(a) Manually operate power window regulator master switch assembly to confirm front passenger side power window functions.

Click here

OK:

Front passenger side power window regulator motors operate by power window regulator master switch assembly

GO TO REMOTE UP / DOWN FUNCTION DOES NOT OPERATE

6.	CHECK FOR DTC*

(a) Check for DTCs and note any codes that are output.

Click here (b) Clear the DTCs.

(b) Clear the DTCs.

Result	Proceed to
No DTCs output	A
DTCs output	B

GO TO DIAGNOSTIC TROUBLE CODE CHART

7.	PROBLEM SYMPTOMS TABLE

(a) Refer to Problem Symptoms Table.

Click here

Result	Proceed to
Fault is not listed in problem symptoms table	A
Fault is listed in problem symptoms table	B

GO TO STEP 9

8.	OVERALL ANALYSIS AND TROUBLESHOOTING*

(a) Operation Check

Click here

(b) Data List / Active Test

Click here (c) Terminals of ECU

Click here

9.	REPAIR OR REPLACE

10.	RESET POWER WINDOW MOTOR

(a) If any of the door window regulators, power window regulator motor assemblies, door glass or door glass runs have been removed and reinstalled, perform "Initialize Power Window Control System" for the applicable door glass.

Click here

11.	CONFIRMATION TEST

END

Precaution

PRECAUTION 1. EXPRESSIONS OF IGNITION SWITCH (a) The type of ignition switch used on this model differs according to the specifications of the vehicle. The expressions listed in the table below ar ...

System Description

SYSTEM DESCRIPTION 1. POWER WINDOW CONTROL SYSTEM DESCRIPTION (a) The power window control system controls the power window operation using the power window regulator motors. The main controls of ...

Other materials:

TC and CG Terminal Circuit
DESCRIPTION DTC output mode is set by connecting terminals TC and CG of the DLC3. The DTCs are displayed by blinking the SRS warning light. HINT: Make sure that DTCs which relate to the CAN communication system are not output. If any of these DTCs are output, check the CAN communicat ...

Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE GENERATOR PULLEY (a) Mount the generator assembly in the vise between aluminum plates. NOTICE: Do not overtighten the vise. (b) Install SST 1-A to the generator pulley shaft. Text in Illustration *a Hold Turn ...

Data List / Active Test
DATA LIST / ACTIVE TEST NOTICE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not. HINT: Using the Techstream to read the Data List allows the values or s ...