Toyota Tacoma (2015-2018) Service Manual: Components
COMPONENTS
ILLUSTRATION
|
*1 |
FRONT ARMREST BASE UPPER PANEL SUB-ASSEMBLY |
*2 |
FRONT DOOR GLASS INNER WEATHERSTRIP |
|
*3 |
FRONT DOOR INSIDE HANDLE BEZEL PLUG |
*4 |
FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY |
|
*5 |
FRONT DOOR LOWER FRAME BRACKET GARNISH |
*6 |
FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
|
*7 |
FRONT NO. 1 SPEAKER ASSEMBLY |
*8 |
NO. 1 DOOR TRIM BRACKET |
ILLUSTRATION
|
*1 |
FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY |
*2 |
FRONT DOOR GLASS RUN |
|
*3 |
FRONT DOOR GLASS SUB-ASSEMBLY |
*4 |
FRONT DOOR SERVICE HOLE COVER |
|
*5 |
FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY |
*6 |
NO. 1 FRONT DOOR SERVICE HOLE COVER |
|
*7 |
NO. 2 FRONT DOOR SERVICE HOLE COVER |
*8 |
OUTER REAR VIEW MIRROR ASSEMBLY |
|
*9 |
POWER WINDOW REGULATOR MOTOR ASSEMBLY |
*10 |
BUTYL TAPE |
.png) |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
.png) |
MP grease |
- |
- |
ILLUSTRATION
|
*1 |
FRONT DOOR DUST PROOF SEAL |
*2 |
FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY |
|
*3 |
FRONT DOOR LOCK ASSEMBLY |
*4 |
FRONT DOOR LOCK OPEN ROD |
|
*5 |
FRONT DOOR OUTSIDE HANDLE ASSEMBLY |
*6 |
FRONT DOOR OUTSIDE HANDLE COVER |
|
*7 |
FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY |
*8 |
FRONT DOOR OUTSIDE HANDLE FRONT PAD |
|
*9 |
FRONT DOOR OUTSIDE HANDLE REAR PAD |
*10 |
FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY |
|
*11 |
HOLE PLATE |
*12 |
DOOR LOCK WIRING HARNESS SEAL |
|
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
|
MP grease |
- |
- |
ILLUSTRATION
|
*A |
for LH Side |
*B |
for RH Side |
|
*C |
for LED Fog Light |
- |
- |
|
*1 |
FRONT DOOR CHECK ASSEMBLY |
*2 |
FRONT DOOR PANEL CUSHION |
|
*3 |
FRONT DOOR PANEL PROTECTOR |
*4 |
FRONT NO. 1 DOOR NAME PLATE |
|
|
N*m (kgf*cm, ft.*lbf) : Specified torque |
● |
Non-reusable part |
|
|
MP grease |
.png) |
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent |
ILLUSTRATION
|
*A |
for Double Cab |
*B |
for Access Cab |
|
*1 |
FRONT DOOR WEATHERSTRIP |
*2 |
HOLE PLATE |
|
*3 |
NO. 1 BLACK OUT TAPE |
- |
- |
|
● |
Non-reusable part |
- |
- |
Adjustment
ADJUSTMENT
CAUTION / NOTICE / HINT
HINT:
Use the same procedures for both the LH and RH sides.
The procedure described below is for the LH side.
Centering bolts are used to mount th ...
Hood
...
Other materials:
Replacement
REPLACEMENT
PROCEDURE
1. REPLACE STRAIGHT PIN
NOTICE:
It is not necessary to remove the straight pin unless it is being replaced.
(a) Using a plastic-faced hammer, tap in new straight pins to the cylinder block.
Text in Illustration
*A
Front Side
*B
...
Initialization
INITIALIZATION
1. INITIALIZE POWER WINDOW CONTROL SYSTEM
NOTICE:
When a door window regulator assembly, power window regulator motor
assembly, door glass or door glass run is reinstalled or replaced, the power
window control system must be initialized. Functions such as the auto u ...
Replacement
REPLACEMENT
PROCEDURE
1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
(a) Start the engine.
(b) Operate the cooler compressor under the conditions shown below:
Item
Condition
Engine Speed
Idling
Operating Time
3 minu ...
