Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Amplifier Box Speaker Assembly

Toyota Tacoma (2015-2018) Service Manual / Audio / Video / Amplifier Box Speaker Assembly

Components

COMPONENTS

ILLUSTRATION

ILLUSTRATION

ILLUSTRATION

Removal

Removal

REMOVAL

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here 3. REMOVE REAR SEATBACK ASSEMBLY RH

3. REMOVE REAR SEATBACK ASSEMBLY RH

(See page 4. REMOVE REAR SEATBACK ASSEMBLY LH )

4. REMOVE REAR SEATBACK ASSEMBLY LH

(See page 5. REMOVE LUGGAGE COMPARTMENT SIDE TRAY LH )

5. REMOVE LUGGAGE COMPARTMENT SIDE TRAY LH

(See page 6. REMOVE LUGGAGE COMPARTMENT SIDE TRAY RH )

6. REMOVE LUGGAGE COMPARTMENT SIDE TRAY RH

(See page 7. REMOVE NO. 1 SPEAKER ASSEMBLY WITH BOX )

7. REMOVE NO. 1 SPEAKER ASSEMBLY WITH BOX

(a) Disconnect the 4 connectors.

(b) Remove the 4 bolts and the No. 1 speaker assembly with box.

(b) Remove the 4 bolts and the No. 1 speaker assembly with box.

Installation

INSTALLATION

PROCEDURE

1. INSTALL NO. 1 SPEAKER ASSEMBLY WITH BOX

(a) Install the No. 1 speaker assembly with box with the 4 bolts.

Torque:

8.4 N·m {86 kgf·cm, 74 in·lbf}

(b) Connect the 4 connectors.

2. INSTALL LUGGAGE COMPARTMENT SIDE TRAY RH

(See page 3. INSTALL LUGGAGE COMPARTMENT SIDE TRAY LH )

3. INSTALL LUGGAGE COMPARTMENT SIDE TRAY LH

(See page 4. INSTALL REAR SEATBACK ASSEMBLY LH )

4. INSTALL REAR SEATBACK ASSEMBLY LH

(See page 5. INSTALL REAR SEATBACK ASSEMBLY RH )

5. INSTALL REAR SEATBACK ASSEMBLY RH

(See page 6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL )

6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:

5.4 N·m {55 kgf·cm, 48 in·lbf}

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here Audio And Visual System

Audio / Video
...

Audio And Visual System
...

Other materials:

System Description
SYSTEM DESCRIPTION 1. GENERAL This system has the following functions: manual slide open and close; auto slide open and close; manual tilt up and down; auto tilt up and down; jam protection; key off operation; key-linked open and close; wireless transmitter-linked open sliding roof open warn ...

On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT STEERING PAD (for Vehicle not Involved in Collision) (a) Perform a diagnostic system check (See page ). (b) With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad ...

Open or Short in Master Cylinder Pressure Sensor (C1421,C1423,C1424,C142A,C1449)
DESCRIPTION DTC No. Detection Item DTC Detection Condition Trouble Area C1421 Open or Short in Master Cylinder Pressure Sensor Any of the following is detected: When voltage at terminal +BS is 9.5 V or ...

© 2011-2024 Copyright www.ttguide.net