TTGuideTacoma manuals & technical reference
Toyota Tacoma (2015-2018) Service Manual / Tire And Wheel / Tire Pressure Warning System / Tire Pressure Monitor ECU Communication Stop (C2179/79)

Toyota Tacoma (2015-2018) Service Manual: Tire Pressure Monitor ECU Communication Stop (C2179/79)

DESCRIPTION

The main body ECU (multiplex network body ECU) sends signals to the tire pressure warning ECU and receiver via a direct line.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Note

C2179/79

Tire Pressure Monitor ECU Communication Stop

Communication between the main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver is interrupted for 10 seconds or more.
  • Main body ECU (Multiplex network body ECU)
  • Wire harness or connector
  • Tire pressure warning ECU and receiver

-

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the Techstream and write them down before removal.
  • It is necessary to perform initialization (See page ) of the transmitter IDs into the tire ) after registration (See page pressure warning ECU and receiver after the ECU has been replaced. ) of the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.
  • If the main body ECU (multiplex network body ECU) is replaced, refer to Registration (See page *: w/ Smart Key System ).*

    *: w/ Smart Key System

PROCEDURE

1.

CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECUAND RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

(a) Disconnect the T14*1, T25*2, T24*3 tire pressure warning ECU and receiver connector.

(b) Disconnect the M6 main body ECU (multiplex network body ECU) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

T14-5 (PRG) - M6-5 (PRG)*1

T25-5 (PRG) - M6-5 (PRG)*2

T24-5 (PRG) - M6-5 (PRG)*3

Always

Below 1 Ω

T14-5 (PRG) or M6-5 (PRG) - Body ground*1

T25-5 (PRG) or M6-5 (PRG) - Body ground*2

T24-5 (PRG) or M6-5 (PRG) - Body ground*3

Always

10 kΩ or higher
  • *1: w/o Wireless Door Lock System
  • *2: w/o Smart Key System with Wireless Door Lock System
  • *3: w/ Smart Key System
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

2.

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

(a) Replace the tire pressure warning ECU and receiver (See page ).

NEXT

3.

CHECK DTC OUTPUT

(a) Clear the DTCs (See page (b) Turn the ignition switch off. ).

(b) Turn the ignition switch off.

(c) Turn the ignition switch to ON.

(d) Check for DTCs (See page OK: ).

OK:

DTC C2179/79 is not output.

OK

END
NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
    Related Tacoma materials

    HD Radio Tuner Malfunction (B1551,B15A0,B15AD,B15B0,B15B3,B15B4,B15B7)
    DESCRIPTION These DTCs are stored when a malfunction occurs in the navigation receiver assembly. DTC No. DTC Detection Condition Trouble Area B1551 When one of the conditions below is met: "HD Radio" tuner decoder ...

    Open in Pump Motor Circuit (C1251)
    DESCRIPTION The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU (master cylinder solenoid). DTC No. DTC Detecting Condition Trouble Areas C1251 ...

    Terminals Of Ecu
    TERMINALS OF ECU 1. CHECK TIRE PRESSURE WARNING ECU AND RECEIVER (a) Disconnect the T14 tire pressure warning ECU and receiver connector and measure the voltage and resistance on the wire harness side. Text in Illustration *A w/o Wireless Door Lock System ...