SYSTEM DESCRIPTION
1. ILLUMINATED ENTRY SYSTEM
(a) The illuminated entry system has the following control functions:
|
Control |
Outline |
Lights that Operate |
|---|---|---|
|
Actuation Area-linked*1 |
When a registered key enters any actuation area around the doors, the lights that operate turn on. |
|
|
When a registered key leaves all of the actuation areas around the doors, the lights that operate turn off. |
||
|
Door Lock/Unlock-linked |
When any door is unlocked, the lights that operate turn on. |
|
|
When all doors are locked, the lights that operate turn off. |
||
|
Door Open/Close-linked |
When any door is opened, the lights that operate turn on. |
|
|
When all doors are closed, the lights that operate turn off. |
||
|
Engine Switch-linked*1 |
When the ignition switch is turned from on or on (ACC) to off, the lights that operate turn on. |
|
|
When the ignition switch is turned from off to ON or ACC, the lights that operate turn off. |
||
|
Ignition Switch-linked*2 |
When the ignition switch is turned from ON or ACC to off, the lights that operate turn on. |
|
|
When the ignition switch is turned from off to ON or ACC, the lights that operate turn off. |
||
|
Delay |
When approximately 15 seconds elapse after any of the following conditions is met, the lights that operate turn off:
|
|
|
Battery Saving |
When 20 minutes elapse after the ignition switch is turned from ACC or ON to off and the lights that operate remain on, the lights are turned off. HINT: Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off.
|
|
|
Interior light auto cut function |
When 20 minutes elapse after the ignition switch is turned from ACC or ON to off and the lights that operate remain on, the lights are turned off. HINT: Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off.
|
|
- *1: w/ Smart Key System
- *2: w/o Smart Key System
2. AUTOMATIC LIGHT CONTROL SYSTEM
(a) When the light control switch is in the AUTO position, the automatic light control system detects ambient light levels and controls the low beam headlights, parking lights, taillights and license plate lights.
3. LIGHT AUTO TURN-OFF SYSTEM
(a) The light auto turn-off system is used to prevent the exterior lights from being accidentally left on (headlights, front fog lights, taillights, parking lights and license plate lights).
This system has the following functions.
|
Function |
Outline |
|---|---|
|
Delay Function |
The exterior lights automatically turn off after 30 seconds when all of the following conditions are met:
|
|
Door Control Transmitter-linked Function |
The exterior lights turn off immediately when the delay function is active and the following condition is met:
|
|
Door Open-linked |
The exterior lights automatically turn off immediately when all of the following conditions are met:
|
4. DAYTIME RUNNING LIGHT SYSTEM
(a) The daytime running light system is designed to automatically illuminate the daytime running lights during the daytime to make the vehicle more visible to other vehicles.
- This system is controlled by the main body ECU (multiplex network body ECU) and daytime running light relay. The main body ECU (multiplex network body ECU) transmits a turn ON signal to the daytime running light relay, which illuminates the daytime running lights.
- This system is enabled when the following conditions are met:
- Ignition switch is ON.
- Engine speed signal is input (engine running).
- Light control switch is in the tail or AUTO position (and the low beam headlights are not turned on via the automatic light control system).
- Parking brake switch is off.
5. AUTOMATIC HIGH BEAM SYSTEM
(a) General
The automatic high beam system enhances the illumination of the area in front of the vehicle to improve visibility for the driver. It works by detecting light from the front of the vehicle, using the forward recognition camera, and turns the high beams of the headlights on or off automatically.
(b) Function of Main Components
|
Component |
Outline |
|---|---|
|
Forward Recognition Camera |
Determines when to turn the high beams on and off after identifying the lights of oncoming vehicles, preceding vehicles and other lights from the picture information of its camera sensor. Then, it sends high beam request signals to the main body ECU (multiplex network body ECU) via CAN communication. |
|
Airbag ECU Assembly (Yaw Rate Sensor) |
Outputs yaw rate information to the forward recognition camera. |
|
Brake Actuator Assembly (Skid Control ECU Assembly) |
Outputs the information about the speed of the wheels. This information is used by the forward recognition camera to turn the high beams on and off. |
|
Combination Meter Assembly |
Turns on the automatic high beam indicator light and displays a message on the multi-information display based on an indicator illumination request signal from the main body ECU (multiplex network body ECU). HINT:
|
|
Main Body ECU (Multiplex Network Body ECU) |
|
|
Auto High Beam Switch |
Enables or disables the automatic high beam system. |
|
ECM |
Outputs a signal to indicate that the shift lever is in R. Based on this signal, the forward recognition camera turns the high beams off. |
(c) Basic Function
(1) When all of the following conditions are met, the automatic high beam system is activated and the automatic high beam indicator light turns on:
- The ignition switch is to ON.
- The light control switch is in the AUTO or head position and the low beam headlights are on.
- The dimmer switch is in the high position.
- The auto high beam switch is ON.
(2) When all of the following conditions are met, the high beams automatically turn on after a short delay:
- Vehicle speed is more than approximately 34 km/h (21 mph).
- The area in front of the vehicle is dark.
- There are no oncoming vehicles with headlights on.
- There are no preceding vehicles with taillights on.
- There are few streetlights along the street ahead.
(3) When any of the following conditions are met, the high beams automatically turn off after a short delay:
- Vehicle speed is less than approximately 27 km/h (17 mph).
- There are oncoming vehicles with headlights on.
- There are preceding vehicles with taillights on.
- Light from streetlights ahead is higher than a specified threshold.
(4) When any of the following conditions are met, the automatic high beam system will be canceled and the indicator light will turn off:
- The ignition switch is turned off.
- The light control switch is turned to any position except the AUTO or head position.
- The dimmer switch is moved to the low position.
- The auto high beam switch is off.
HINT:
It is possible to manually turn the high beams on and off by performing either of the following operations:
- When changing the high beams controlled by the automatic high beam system to the low beams manually, move the dimmer switch to the low position. The automatic high beam system will be canceled and the low beams will be turned on. To enable the automatic high beam system again, move the dimmer switch to the high position.
- When changing the low beams controlled by the automatic high beam system to the high beams manually, turn the auto high beam switch off. The automatic high beam system will be canceled and the high beams will be turned on. To enable the automatic high beam system again, turn the auto high beam switch on.
HINT:
The automatic high beam system monitors the area in front of the vehicle using the forward recognition camera and makes a judgment to turn on the high beams when the surrounding area is dark (there are no headlights from oncoming vehicles and no taillights from preceding vehicles). High beam control limitations:
- When the surrounding area is not dark enough, the high beams will not turn on even if the low beam headlights are turned on by the automatic light control system and the automatic high beam indicator light on the combination meter assembly illuminates. (The light level sufficient to turn the auto low beams on is not the same as the light level required to automatically change the low beams to high beams.)
- When an oncoming vehicle suddenly appears at a sharp curve or a vehicle crosses the path of the vehicle, the high beams may remain on.
- When the fog lights of an oncoming vehicle are detected, the high beams may be turned off.
- The timing of the high beams turning on and off may differ depending on the brightness of headlights or fog lights from oncoming vehicles or the taillights of preceding vehicles.
- The timing of the high beams turning on and off may differ between normal conditions (good weather) and when driving on wet, frozen or snowy roads.
- The timing of the high beams turning on and off may differ depending on the number of occupants and amount of cargo present.
- Be aware that on some occasions, the high beams may switch on and off unexpectedly.
HINT:
The forward recognition camera continually monitors the light level in the area in front of the vehicle. There is a delay in turning on the high beams. Even when there is no ambient light, the high beams will not turn on immediately. The delay will vary depending on the situation.
