Toyota Tacoma (2015-2018) Service Manual: Rear Left Center Sensor Malfunction (C1AE7)
DESCRIPTION
The No. 1 ultrasonic sensor (rear center sensor LH) is installed on the rear bumper. The ECU detects obstacles based on signals received from the No. 1 ultrasonic sensor (rear center sensor LH). If the No. 1 ultrasonic sensor (rear center sensor LH) has an open circuit or other malfunction, it will not function normally.
|
DTC No. |
DTC Detection Condition |
Trouble Area |
|---|---|---|
|
C1AE7 |
A malfunction of the No. 1 ultrasonic sensor (rear center sensor LH). |
|
CAUTION / NOTICE / HINT
NOTICE:
If DTCs are output after repairs, turn the ignition switch to ON and turn the
back sonar or clearance sonar switch assembly on. Then clear the DTCs (See page
.gif)
).
PROCEDURE
|
1. |
CHECK DTC OUTPUT |
(a) Check for DTCs (See page ).
|
Result |
Proceed to |
|---|---|
|
Only DTC C1AE7 is output |
A |
|
DTC C1AE7 and C1AED are output |
B |
|
No DTCs are output |
C |
| B | .gif) |
GO TO DTC (C1AED) |
| C | |
USE SIMULATION METHOD TO CHECK |
|
.gif)
|
2. |
REPLACE NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR LH) |
(a) Replace the No. 1 ultrasonic sensor (rear center sensor LH) with a known
good one (See page ).
HINT:
All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
|
|
3. |
CHECK DTC OUTPUT |
(a) Clear the DTCs (See page ).
(b) Check for DTCs (See page ).
|
Result |
Proceed to |
|---|---|
|
No DTCs are output |
OK |
|
DTC C1AE7 is output |
NG |
| OK | |
END (REAR CENTER SENSOR LH WAS DEFECTIVE) |
| NG | |
REPLACE CLEARANCE WARNING ECU ASSEMBLY |
Rear Sensor Communication Malfunction (C1AED)
DESCRIPTION
This DTC is stored when there is an open or short circuit in the communication
line between the rear sensors and the ECU, or when there is a malfunction in a rear
sensor.
...
Clearance Sonar Main Switch Circuit
DESCRIPTION
The back sonar or clearance sonar switch assembly is installed at the base of
the driver side of the instrument panel.
When the back sonar or clearance sonar switch assembly is turned ...
Other materials:
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK
(a) Connect the Techstream to the DLC3.
(1) Turn the ignition switch to ON.
NOTICE:
Do not start the engine.
(2) Turn the Techstream on.
(3) Enter the following menus: Powertrain / Engine / Active Test / C ...
Disassembly
DISASSEMBLY
CAUTION / NOTICE / HINT
NOTICE:
Do not try to remove the black nylon tube as it is welded to the fuel suction
tube assembly (See page
).
PROCEDURE
1. REMOVE FUEL SENDER GAUGE ASSEMBLY
2. REMOVE NO. 1 FUEL SUB-TANK
(a) Disconnect the 2 fuel pump connectors.
...
Air Conditioning Compressor Magnetic Clutch Circuit
DESCRIPTION
When the air conditioning amplifier assembly is turned on, a magnetic clutch
on signal is sent from the MGC terminal of the air conditioning amplifier assembly.
Then, the MG CLT relay turns on to operate the magnetic clutch assembly.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NO ...
