TTGuideTacoma manuals & technical reference
Toyota Tacoma (2015-2018) Service Manual / Brake Control / Dynamic Control Systems / Vehicle Stability Control System(for Vacuum Brake Booster) / Open or Short in Master Cylinder Pressure Sensor (C1421,C1423,C1424,C142A,C1449)

Toyota Tacoma (2015-2018) Service Manual: Open or Short in Master Cylinder Pressure Sensor (C1421,C1423,C1424,C142A,C1449)

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1421

Open or Short in Master Cylinder Pressure Sensor

Any of the following is detected:

  • When voltage at terminal +BS is 9.5 V or higher, power supply voltage of master cylinder pressure sensor is continuously low for 1 second or more.
  • When master cylinder pressure sensor power supply voltage has risen, master cylinder pressure sensor has overheated or overcurrent of master cylinder pressure sensor continues for 0.1 seconds or more.
  • When +BS terminal voltage is 9.5 to 17.4 V, there is no communication with master cylinder pressure sensor continuously for 0.1 seconds or more.

Brake actuator assembly (Master cylinder pressure sensor)

C1423

Master Cylinder Pressure Sensor Zero Point Low Malfunction

Master cylinder pressure is below -0.744 MPa (-7.6 kgf/cm2, -107 psi) for 5 seconds or more.

Brake actuator assembly (Master cylinder pressure sensor)

C1424

Master Cylinder Pressure Sensor Output Malfunction

Any of the following is detected:

  • When vehicle speed is 7 km/h (4.3 mph) or more and master cylinder pressure exceeds 1.764 MPa (18.0 kgf/cm2, 255 psi), master cylinder pressure does not increase 0.048 MPa (0.5 kgf/cm2, 6.9 psi) or more continuously for 60 seconds.
  • When vehicle speed is 7 km/h (4.3 mph) and master cylinder pressure is 2.45 MPa (25.0 kgf/cm2, 355 psi) or more, master cylinder pressure does not increase 0.048 MPa (0.5 kgf/cm2, 6.9 psi) or more continuously for 30 seconds.
  • Master cylinder pressure does not increase 0.048 MPa (0.5 kgf/cm2, 6.9 psi) or more 5 times or more while vehicle speed decreases from 40 km/h (25 mph) to 0 km/h (0 mph).
  • When vehicle speed is 10 km/h (6 mph) or more, noise in master cylinder pressure value occurs 7 times or more in 5 seconds.
  • When vehicle speed is 7 km/h (4.3 mph) or more, braking is performed (stop light switch assembly is ON) and master cylinder pressure differential value is below 20 MPa/s, difference between master cylinder pressure estimated from vehicle deceleration and master cylinder pressure sensor input value is large for 1 second or more 5 times or more.

Brake actuator assembly (Master cylinder pressure sensor)

C142A

Master Cylinder Pressure Sensor Internal Malfunction

Any of the following is detected:

  • Master cylinder pressure is 23.328 MPa (237.8 kgf/cm2, 3382 psi) or more continuously for 0.1 seconds.
  • Master cylinder temperature is 150°C (302°F) or more continuously for 0.1 seconds.

Brake actuator assembly (Master cylinder pressure sensor)

C1449

Master Cylinder Output Value Malfunction

Master cylinder pressure sensor invalid condition continues for 0.2 seconds or more.

Brake actuator assembly (Master cylinder pressure sensor)

HINT:

DTC will be output when conditions for any of the patterns in the table above are met.

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (See page PROCEDURE PROCEDURE ).

PROCEDURE

1.

REPLACE BRAKE ACTUATOR ASSEMBLY

(a) Replace the brake actuator assembly (master cylinder pressure sensor) (See page ).

NEXT

END

    Related Tacoma materials

    USB Media Malfunction (B1585)
    DESCRIPTION This DTC is stored when a malfunction occurs in a connected device. DTC No. DTC Detection Condition Trouble Area B1585 USB Device Malfunction ...

    Master Cylinder Pressure Sensor Zero Point High Malfunction (C1422)
    DESCRIPTION DTC No. Detection Item DTC Detection Condition Trouble Area C1422 Master Cylinder Pressure Sensor Ze ...

    Replacement
    REPLACEMENT PROCEDURE 1. REPLACE INTAKE VALVE GUIDE BUSH (a) Heat the cylinder head to 80 to 100°C (176 to 212°F). (b) Place the cylinder head on wooden blocks. (c) Using SST and a hammer, tap out the intake valve guide bushes. SST: 09201-10000 09201-01050 SST: 09950-70010 ...