Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Installation

INSTALLATION

CAUTION / NOTICE / HINT

NOTICE:

Replace the blind spot monitor sensor if it has been dropped or subjected to a severe impact.

PROCEDURE

1. INSTALL BLIND SPOT MONITOR SENSOR LH

(a) Install the blind spot monitor sensor LH with the 3 nuts.

Torque:

9.0 N·m {92 kgf·cm, 80 in·lbf}

(b) Connect the connector.

2. INSTALL BLIND SPOT MONITOR SENSOR RH

HINT:

Use the same procedure as for the LH side.

3. PERFORM BLIND SPOT MONITOR BEAM AXIS INSPECTION

(See page ) ) 4. PERFORM DIAGNOSTIC SYSTEM CHECK )

4. PERFORM DIAGNOSTIC SYSTEM CHECK

(See page 5. INSTALL REAR BUMPER EXTENSION LH (w/ Towing Package) )

5. INSTALL REAR BUMPER EXTENSION LH (w/ Towing Package)

(See page 6. INSTALL REAR BUMPER EXTENSION LH (w/o Towing Package) )

6. INSTALL REAR BUMPER EXTENSION LH (w/o Towing Package)

(See page 7. INSTALL REAR BUMPER EXTENSION RH (w/ Towing Package) )

7. INSTALL REAR BUMPER EXTENSION RH (w/ Towing Package)

HINT:

Use the same procedure as for the LH side.

8. INSTALL REAR BUMPER EXTENSION RH (w/o Towing Package)

HINT:

Use the same procedure as for the LH side.

9. INSTALL REAR BUMPER PAD SUB-ASSEMBLY (w/ Towing Package)

(See page 10. INSTALL REAR BUMPER PAD SUB-ASSEMBLY (w/o Towing Package) )

10. INSTALL REAR BUMPER PAD SUB-ASSEMBLY (w/o Towing Package)

(See page 11. INSTALL CONNECTOR COVER (w/ Towing Package) )

11. INSTALL CONNECTOR COVER (w/ Towing Package)

(See page 12. INSTALL REAR BUMPER HOLE COVER (w/o Towing Package) )

12. INSTALL REAR BUMPER HOLE COVER (w/o Towing Package)

(See page 13. INSTALL REAR BUMPER ASSEMBLY (w/ Towing Package) )

13. INSTALL REAR BUMPER ASSEMBLY (w/ Towing Package)

HINT:

(See page 14. INSTALL REAR BUMPER ASSEMBLY (w/o Towing Package) )

14. INSTALL REAR BUMPER ASSEMBLY (w/o Towing Package)

HINT:

(See page Blind Spot Monitor System )

Removal
REMOVAL CAUTION / NOTICE / HINT NOTICE: Replace the blind spot monitor sensor if it has been dropped or subjected to a severe impact. PROCEDURE 1. REMOVE REAR BUMPER ASSEMBLY (w/ Towing Package ...

Blind Spot Monitor System
...

Other materials:

Open in Pump Motor Circuit (C1251)
DESCRIPTION The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU (master cylinder solenoid). DTC No. DTC Detecting Condition Trouble Areas C1251 ...

Dtc Check / Clear
DTC CHECK / CLEAR 1. DTC CHECK USING TECHSTREAM (a) Connect the Techstream to the DLC3. (b) Turn the ignition switch to ON. (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Air Conditioner / Trouble Codes. (e) Check for DTCs. 2. DTC CLEAR USING TECHSTREAM (a) Conn ...

Engine Coolant Temperature Receiver Gauge Malfunction
DESCRIPTION In this circuit, the meter CPU receives engine coolant temperature signals from the ECM using the CAN communication system (CAN V1 Bus). The meter CPU displays engine coolant temperature that is calculated based on the data received from the ECM. WIRING DIAGRAM CAUTION / NOTIC ...

© 2011-2025 Copyright www.ttguide.net