Toyota Tacoma (2015-2018) Service Manual: Cellular Phone Inspection

Toyota Tacoma (2015-2018) Service Manual / Audio / Video / Audio And Visual System / Cellular Phone Inspection

PROCEDURE

1.	CHECK USAGE CONDITION

(a) Check that the vehicle and cellular phone meet the following conditions:

NOTICE:

If changing cellular phone settings, updating software, etc. is necessary, make sure to obtain the permission of the customer before performing it.

The cellular phone is "Bluetooth" compatible (See page ).
The cellular phone is registered as a hands-free device.
"Bluetooth" setting of the cellular phone is on.
Operating system and software of the cellular phone are the latest versions.
There are no other radio wave emitting devices ("Wi-Fi" communication device, etc.) in the cabin.

(b) Connect the cellular phone to the in-vehicle device and check that it is connected correctly.

Result

Result	Proceed to
The cellular phone is connected correctly	A
The cellular phone is not connected correctly	B

END

2.	RESTART CELLULAR PHONE

(a) Restart the cellular phone.

(b) Turn the ignition switch off.

(d) Connect the cellular phone to the in-vehicle device and check that it is connected correctly.

Result

Result	Proceed to
The cellular phone is connected correctly	A
The cellular phone is not connected correctly	B

END

3.	CHECK RECEPTION

(a) Check if the in-vehicle device can be recognized by the cellular phone.

Result

Result	Proceed to
In-vehicle device can be recognized	A
In-vehicle device cannot be recognized	B

GO TO STEP 5

4.	REGISTER AGAIN

(a) Clear all "Bluetooth" devices registered to the radio and display receiver assembly and delete the radio and display receiver assembly information from the cellular phone.

(b) Register the cellular phone again.

Result

Result	Proceed to
The cellular phone is connected correctly	A
The cellular phone is not connected correctly	B

END

5.	CHECK USING ANOTHER VEHICLE

(a) Check if the customer's cellular phone functions normally using another "Bluetooth" compatible vehicle.

HINT:

Make sure to obtain the customer's permission to perform this procedure.
After the inspection, clear the registered information and usage history acquired during the inspection.

Result

Result	Proceed to
The cellular phone is connected correctly	A
The cellular phone is not connected correctly	B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

6.	CHECK USING ANOTHER CELLULAR PHONE

(a) Check if the system functions normally using another "Bluetooth" compatible cellular phone.

HINT:

Make sure to obtain the customer's permission to perform this procedure.
After the inspection, clear the registered information and usage history acquired during the inspection.

Result

Result	Proceed to
The cellular phone is connected correctly	A
The cellular phone is not connected correctly	B

END (ONLY A "Bluetooth" COMPATIBLE CELLULAR PHONE CAN BE USED)

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

Cellular Phone Registration Failure

PROCEDURE 1. CHECK USAGE CONDITION (a) Check that the vehicle and cellular phone meet the following conditions: NOTICE: If changing cellular phone settings, updatin ...

Confirm Cellular Phone Functionality

PROCEDURE 1. CHECK CUSTOMER'S CELLULAR PHONE COMPATIBILITY (a) Check if the cellular phone is compatible (Refer to http://www.toyota.com/entune/). Result ...

Other materials:

Removal
REMOVAL CAUTION / NOTICE / HINT HINT: If the bumper is damaged, there is a possibility that the installation area of the blind spot monitor sensor may be deformed and the blind spot monitor system may not operate correctly, so visually inspect the blind spot monitor sensor installation area ...

Installation
INSTALLATION PROCEDURE 1. INSTALL NO. 1 ULTRASONIC SENSOR HINT: Use the same procedure for both sides. (a) Engage the 4 claws to install the 4 No. 1 ultrasonic sensors as shown in the illustration. 2. INSTALL REAR BUMPER EXTENSION LH (w/ Towing Package) (See page ) 3. INSTALL REAR BUMPE ...

Cruise Main Indicator Light Circuit
DESCRIPTION When the dynamic radar cruise control system is turned on using the cruise control main switch (ON-OFF button), the cruise control indicator (vehicle-to-vehicle distance control mode) illuminates. The ECM uses this and other indicators to indicate the control condition (presence o ...