INSTALLATION
PROCEDURE
1. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1)
(a) Apply engine oil to a new O-ring and install it to the camshaft timing oil control solenoid assembly in the locations shown in the illustration. Text in Illustration
|
|
(b) Install the camshaft timing oil control solenoid assembly to the timing chain cover assembly with 2 new bolts.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
NOTICE:
Be careful that the O-ring is not jammed.
(c) Connect the connector to the camshaft timing oil control solenoid assembly.
2. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1)
(a) Apply engine oil to a new O-ring and install it to the camshaft timing oil control solenoid assembly in the locations shown in the illustration. Text in Illustration
|
|
(b) Install the camshaft timing oil control solenoid assembly to the timing chain cover assembly with 2 new bolts.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
NOTICE:
Be careful that the O-ring is not jammed.
(c) Connect the connector to the camshaft timing oil control solenoid assembly.
3. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)
(a) Apply engine oil to a new O-ring and install it to the camshaft timing oil control solenoid assembly in the locations shown in the illustration. Text in Illustration
|
|
(b) Install the camshaft timing oil control solenoid assembly to the timing chain cover assembly with 2 new bolts.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
NOTICE:
Be careful that the O-ring is not jammed.
(c) Connect the connector to the camshaft timing oil control solenoid assembly.
4. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2)
(a) Apply engine oil to a new O-ring and install it to the camshaft timing oil control solenoid assembly in the locations shown in the illustration. Text in Illustration
|
|
(b) Install the camshaft timing oil control solenoid assembly to the timing chain cover assembly with 2 new bolts.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
NOTICE:
Be careful that the O-ring is not jammed.
(c) Connect the connector to the camshaft timing oil control solenoid assembly.
5. INSTALL THROTTLE BODY BRACKET
(a) Install the throttle body bracket to the intake air surge tank assembly and timing chain cover assembly with the 2 bolts.
Torque:
21 N·m {214 kgf·cm, 15 ft·lbf}
6. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
(a) Apply engine oil to a new O-ring and install it to the engine oil level dipstick guide.
(b) Install the engine oil level dipstick guide to the timing chain cover assembly and oil pan sub-assembly with the bolt.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
(c) Engage the clamp to install the wire harness.
(d) Install the engine oil level dipstick.
7. INSTALL AIR CLEANER CAP AND HOSE
8. INSTALL V-BANK COVER SUB-ASSEMBLY
9. INSTALL FRONT FENDER SEAL RH
HINT:
Use the same procedure as for the LH side (See page ).
Jam Protection Function does not Operate
DESCRIPTION
This symptom may occur for any of the windows.
The jam protection function operates within a specified range during the manual
up or auto up operation.
CAUTION / NOTICE / HINT
NOTICE:
If a power window regulator motor assembly has been replaced with a
new one, initiali ...
Precaution
PRECAUTION
1. IGNITION SWITCH EXPRESSIONS
(a) The type of ignition switch used on this model differs according to the specifications
of the vehicle. The expressions listed in the table below are used in this section.
Expression
Ignition Switch (Position)
Engine ...
Terminals Of Ecu
TERMINALS OF ECU
1. CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND DRIVER SIDE JUNCTION
BLOCK
(a) Disconnect the main body ECU (multiplex network body ECU) connectors.
Text in Illustration
*1
Main Body ECU (Multiplex Network Body ECU)
-
-
...