Toyota Tacoma (2015-2018) Service Manual: Side Moulding

Toyota Tacoma (2015-2018) Service Manual / Exterior / Side Moulding

Components

COMPONENTS

ILLUSTRATION

Removal

REMOVAL

CAUTION / NOTICE / HINT

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
When removing the lower No. 2 side panel moulding, heat the vehicle body and lower No. 2 side panel moulding using a heat light.

Heating Temperature

Item	Temperature
Vehicle Body	40 to 60°C (104 to 140°F)
Lower No. 2 Side Panel Moulding	20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the vehicle body or lower No. 2 side panel moulding excessively.

PROCEDURE

1. REMOVE LOWER NO. 2 SIDE PANEL MOULDING (w/ Over Fender)

(a) Using a heat light, heat the lower No. 2 side panel moulding.

(b) Remove the screw.

Text in Illustration

*a	Double-sided Tape

2. REMOVE LOWER NO. 2 SIDE PANEL MOULDING (w/o Over Fender)

(a) Using a heat light, heat the lower No. 2 side panel moulding.

(b) Remove the 2 screws.

Text in Illustration

*a	Double-sided Tape

Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
When installing the lower No. 2 side panel moulding, heat the vehicle body and lower No. 2 side panel moulding using a heat light.

PROCEDURE

1. INSTALL LOWER NO. 2 SIDE PANEL MOULDING (w/ Over Fender)

(a) Clean the vehicle body surface.

(1) Using a heat light, heat the vehicle body surface.

(2) Remove the double-sided tape from the vehicle body.

(3) Clean off any tape adhesive residue with cleaner.

(b) Install a new lower No. 2 side panel moulding.

(1) Using a heat light, heat the vehicle body and a new lower No. 2 side panel moulding.

(2) Remove the release paper from the lower No. 2 side panel moulding.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.

(3) Engage the claws to install the lower No. 2 side panel moulding.

Text in Illustration

*a	Double-sided Tape

(4) Install the screw.

2. INSTALL LOWER NO. 2 SIDE PANEL MOULDING (w/o Over Fender)

(a) Clean the vehicle body surface.

(1) Using a heat light, heat the vehicle body surface.

(2) Remove the double-sided tape from the vehicle body.

(3) Clean off any tape adhesive residue with cleaner.

(b) Install a new lower No. 2 side panel moulding.

(1) Using a heat light, heat the vehicle body and a new lower No. 2 side panel moulding.

(2) Remove the release paper from the lower No. 2 side panel moulding.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.

(3) Engage the claws to install the lower No. 2 side panel moulding.

Text in Illustration

*a	Double-sided Tape

(4) Install the 2 screws.

Installation

INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. When installing a roof drip side mou ...

Tail Gate Protector

Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE TAIL GATE PROTECTOR (a) Using a T30 "TORX" socket wrench, remove the 8 screws. ...

Other materials:

Air Outlet Damper Position Sensor Circuit (B1433/33)
DESCRIPTION This sensor detects the position of the mode damper and sends the appropriate signals to the air conditioning amplifier assembly. The position sensor is built into the No. 1 air conditioning radiator damper servo sub-assembly (for mode switching). DTC No. DTC ...

Confirm Cellular Phone Functionality
PROCEDURE 1. CHECK CUSTOMER'S CELLULAR PHONE COMPATIBILITY (a) Check if the cellular phone is compatible (Refer to http://www.toyota.com/entune/). Result Result Proceed to Cellular phone is compatible A ...

Vacuum Warning Switch
Components COMPONENTS ILLUSTRATION On-vehicle Inspection ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT BRAKE FLUID LEVEL IN RESERVOIR 2. INSPECT BRAKE BOOSTER ASSEMBLY 3. INSPECT VACUUM WARNING SWITCH ASSEMBLY (a) Start the engine and stop it after 1 or 2 minutes. (b) Disconnect the ...