OPERATION CHECK
1. INSPECT INTERIOR LIGHT CONTROL OPERATION
NOTICE:
Perform this inspection with the customize parameters at the default settings.
The interior light control illuminates the lights below.
(a) The operations and conditions of this control are described below.
Operation |
Condition |
---|---|
Fade in and illuminate constantly |
Any door is opened when all doors are closed. |
Illuminate for 15 seconds, and then fade out |
When any of the following conditions is met, the interior lights illuminate for 15 seconds, and then fade out:
|
Fade out immediately |
When any of the following conditions is met, the interior lights fade out immediately:
|
2. INSPECT BATTERY SAVING CONTROL OPERATION
NOTICE:
Perform this inspection with the customize parameters at the default settings.
The lights controlled by the battery saving control are as follows:
(a) The operation and conditions of this control are described below.
Operation |
Condition |
---|---|
Battery saving |
When 20 minutes elapse after the ignition switch is turned from ON or ACC to off and the lights that operate remain on, the lights are turned off. HINT: Battery saving control is canceled when any of the following operations is performed before the lights are turned off by the battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off.
|
Interior light auto cut function |
When 20 minutes elapse after the ignition switch is turned from ACC or ON to off and the lights that operate remain on, the lights are turned off. HINT: Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off.
|
3. AUTOMATIC LIGHT CONTROL SYSTEM OPERATION CHECK
(a) Turn the ignition switch to ON.
(b) Turn the light control switch to the AUTO position.
(c) Cover the automatic light control sensor.
(d) Check that the taillights and low beam headlights come on.
(e) Uncover the automatic light control sensor.
(f) Check that the low beam headlights and taillights go off.
4. LIGHT AUTO TURN-OFF SYSTEM OPERATION CHECK
(a) When the taillights are on (headlights are not on)
(1) Close all of the doors.
(2) Turn the ignition switch to ON.
(3) Turn the taillights on.
(4) Turn the ignition switch off.
(5) Open the driver door.
(6) Check that all of the lights turn off immediately.
(b) When the headlights are on
(1) Close all of the doors.
(2) Turn the ignition switch to ON.
(3) Turn the headlights on.
(4) Turn the ignition switch off.
(5) Open any of the doors.
(6) Close the door.
(7) Check that all of the lights turn off after 30 seconds (delay function).
HINT:
Before the lights turn off, if the lock button on the key is pushed after all of the doors are locked, all of the lights will turn off immediately.
5. DAYTIME RUNNING LIGHT SYSTEM OPERATION CHECK
(a) Turn the light control switch to the tail or AUTO position (and the low beam headlights are not turned on via the automatic light control system).
(b) Start the engine.
(c) Release the parking brake.
(d) Check that the daytime running lights come on.
6. AUTOMATIC HIGH BEAM SYSTEM OPERATION CHECK
(a) Check the operation of the automatic high beam indicator light.
*a |
Automatic High Beam Indicator Light |
(1) Turn the ignition switch to ON.
(2) Turn the light control switch to the AUTO or head position.
(3) Turn the dimmer switch to the high position.
(4) Press the auto high beam switch.
HINT:
If the auto high beam switch is turned on when the light control switch is not in the AUTO or head position, or the dimmer switch is not in the high position, "Auto High Beam Ready Turn ON High Beam to Activate" will be displayed on the multi-information display.
(5) Check that the automatic high beam indicator light comes on.
(b) Check the operation of the automatic high beam function.
(1) At night, when driving the vehicle with the automatic high beam system in standby mode, check that the high beams automatically turn on after a short delay when all of the following conditions are met:
(2) At night, when driving the vehicle with the high beams turned on by the automatic high beam system, check that the automatic high beam system turns off the high beams and returns to standby mode when any of the following conditions are met:
Brake Switch "A" Circuit Open (P057113)
DESCRIPTION
DTC No.
DTC Detection Condition
Trouble Area
MIL
Note
P057113
Vehicle Condition:
Cruise control operating
Malfunction Status:
Stop light switch assembly circuit malfunction ...
Tire Pressure Monitor Receiver Communication Stop (B1247)
DESCRIPTION
The main body ECU (multiplex network body ECU) and tire pressure warning ECU
and receiver are connected using 2 direct lines that they use to communicate with
each other.
DTC No.
Detection Item
DTC Detection Condition
Trouble Area
...
Brake System Malfunction (C1A50)
DESCRIPTION
When the pre-collision system is operating, the millimeter wave radar sensor
assembly sends brake control signals to the skid control ECU (master cylinder solenoid)*1
or skid control ECU (brake actuator assembly)*2.
If the millimeter wave radar sensor assembly receives a vehicle st ...