DESCRIPTION
The main body ECU (multiplex network body ECU) controls the low beam headlights.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
PROCEDURE
1. |
PERFORM ACTIVE TEST USING TECHSTREAM (HEADLIGHT RELAY) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Main Body
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
---|---|---|---|
Headlight Relay |
Headlight relays |
ON/OFF |
- |
OK:
Headlight relays operate. (Low beam headlights illuminate.)
OK |
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
2. |
INSPECT H-LP LO RELAY |
(a) Remove the H-LP LO relay from the engine room relay block. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
3 - 5 |
Voltage is not applied between terminals 1 and 2 |
10 kΩ or higher |
3 - 5 |
Voltage is applied between terminals 1 and 2 |
Below 1 Ω |
NG |
REPLACE H-LP LO RELAY |
|
3. |
CHECK HARNESS AND CONNECTOR (BATTERY - H-LP LO RELAY) |
(a) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
Relay terminal 2 - Body ground |
Always |
11 to 14 V |
Relay terminal 5 - Body ground |
Always |
11 to 14 V |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
4. |
CHECK HARNESS AND CONNECTOR (H-LP LO RELAY - DRIVER SIDE JUNCTION BLOCK) |
(a) Disconnect the 1F driver side junction block connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
Relay terminal 1 - 1F-28 |
Always |
Below 1 Ω |
1F-28 - Body ground |
Always |
10 kΩ or higher |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
5. |
INSPECT DRIVER SIDE JUNCTION BLOCK |
(a) Remove the driver side junction block. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
1F-28 - MB-15 (HRLY) |
Always |
Below 1 Ω |
1F-28 - Body ground |
Always |
10 kΩ or higher |
*a |
Component without harness connected (Driver Side Junction Block) |
OK |
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
NG |
REPLACE DRIVER SIDE JUNCTION BLOCK |
Voltage Inverter
Components
COMPONENTS
ILLUSTRATION
Inspection
INSPECTION
PROCEDURE
1. INSPECT VOLTAGE INVERTER ASSEMBLY
(a) Check the voltage inverter assembly.
(1) Measure the voltage according to the value(s) in the table below.
Text in Illustration
*a
Component with harness ...
Installation
INSTALLATION
PROCEDURE
1. INSTALL HYDRAULIC BRAKE BOOSTER
(a) Install a new brake booster gasket onto the hydraulic brake booster.
(b) Install the hydraulic brake booster with the 4 nuts.
Torque:
14 N·m {145 kgf·cm, 10 ft·lbf}
(c) Using a union nut wrench, connect the 4 brake l ...
Automatic High Beam System (B124B)
DESCRIPTION
The main body ECU (multiplex network body ECU) determines the status of the automatic
high beam system based on the automatic high beam system signal from the forward
recognition camera.
DTC No.
Detection Item
DTC Detection Condition
Trou ...