INSTALLATION
PROCEDURE
1. ADJUST COMPRESSOR OIL
(a) for HFC-134a (R134a):
(1) When replacing the compressor and magnetic clutch with new ones, after gradually discharging the refrigerant gas from the service valve, drain the following volume of oil from new compressor and magnetic clutch before installation.
Standard:
(Oil capacity inside a new compressor and magnetic clutch: 150 + 15 cc (5.1 + 0.51 fl.oz.)) - (Remaining oil amount in the removed compressor and magnetic clutch) = (Oil amount to be removed when replacing the compressor)
NOTICE:
(b) for HFO-1234yf (R1234yf):
(1) When replacing the compressor and magnetic clutch with new ones, after gradually discharging the refrigerant gas from the service valve, drain the following volume of oil from new compressor and magnetic clutch before installation.
Standard:
(Oil capacity inside a new compressor and magnetic clutch: 150 + 15 cc (5.1 + 0.51 fl.oz.)) - (Remaining oil amount in the removed compressor and magnetic clutch) = (Oil amount to be removed when replacing the compressor)
NOTICE:
2. INSTALL COOLER COMPRESSOR ASSEMBLY (for 2TR-FE)
(a) Using an E8 ''TORX'' socket wrench, temporarily install the cooler compressor assembly with the 2 stud bolts.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
(b) Install the 2 nuts and 2 bolts in the order shown in the illustration. Torque: 21 N·m {214 kgf·cm, 16 ft·lbf} |
|
(c) Connect the connector.
3. INSTALL COOLER COMPRESSOR ASSEMBLY (for 2GR-FKS)
(a) Using an E8 ''TORX'' socket wrench, temporarily install the cooler compressor assembly with the 2 stud bolts.
(b) Install the 2 nuts and 2 bolts in the order shown in the illustration. Torque: 21 N·m {214 kgf·cm, 16 ft·lbf} |
|
(c) Connect the connector.
4. INSTALL DISCHARGE HOSE SUB-ASSEMBLY
(a) Remove the vinyl tape from discharge hose sub-assembly and connecting portion of the cooler compressor assembly.
(b) Apply sufficient compressor oil to a new O-ring and fitting surface of the cooler compressor assembly.
Compressor oil:
PSD1 or equivalent
(c) Install the O-ring to the discharge hose sub-assembly.
(d) Install the discharge hose sub-assembly to the cooler compressor assembly with the bolt.
Torque:
9.8 N·m {100 kgf·cm, 87 in·lbf}
5. INSTALL SUCTION HOSE SUB-ASSEMBLY (for 2TR-FE)
(a) Remove the vinyl tape from the suction hose sub-assembly.
(b) Apply sufficient compressor oil to a new O-ring and fitting surface of the cooler compressor assembly.
Compressor oil:
PSD1 or equivalent
(c) Install the O-ring to the suction hose sub-assembly.
(d) Install the suction hose sub-assembly to the cooler compressor assembly with the bolt.
Torque:
9.8 N·m {100 kgf·cm, 87 in·lbf}
(e) Install the suction hose sub-assembly with the bolt.
Torque:
7.5 N·m {76 kgf·cm, 66 in·lbf}
6. INSTALL SUCTION HOSE SUB-ASSEMBLY (for 2GR-FKS)
(a) Remove the vinyl tape from the suction hose sub-assembly.
(b) Apply sufficient compressor oil to a new O-ring and fitting surface of the cooler compressor assembly.
Compressor oil:
PSD1 or equivalent
(c) Install the O-ring to the suction hose sub-assembly.
(d) Install the suction hose sub-assembly to the cooler compressor assembly with the bolt.
Torque:
9.8 N·m {100 kgf·cm, 87 in·lbf}
(e) Install the suction hose sub-assembly with the bolt.
Torque:
7.5 N·m {76 kgf·cm, 66 in·lbf}
7. INSTALL FRONT UPPER FENDER APRON SEAL
(a) Install the front upper fender apron seal with the 5 clips.
8. INSTALL GENERATOR ASSEMBLY (for 2GR-FKS)
Click here
9. INSPECT FAN AND GENERATOR V BELT (for 2TR-FE)
Click here
10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Torque:
5.4 N·m {55 kgf·cm, 48 in·lbf}
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
11. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
Click here
12. WARM UP ENGINE
Click here
13. INSPECT FOR REFRIGERANT LEAK
Click here
Vehicle load limits
Vehicle load limits include total load capacity, seating capacity, TWR (Trailer
Weight Rating) and cargo capacity.
■ Total load capacity (vehicle capacity weight):
Total load capacity means the combined weight of occupants, cargo and luggage.
■ Seating capacity:
Regular Cab models ...
Operation History List
OPERATION HISTORY LIST
NOTICE:
The cause of a malfunction is stored in the RAM or EEPROM in the certification
ECU (smart key ECU assembly). As the cause of a malfunction stored in the
RAM will be cleared when the cable is disconnected from the negative (-)
battery terminal, do ...
Operation Check
OPERATION CHECK
CHECK PRE-COLLISION SYSTEM SETTING
(a) Turn the ignition switch to ON.
(b) Operate the steering pad switch assembly to change the setting of PCS on
the multi-information display to "On" and check that the pre-collision system turns
on.
HINT:
When the ignition switc ...