Toyota Tacoma (2015-2018) Service Manual: Disassembly
DISASSEMBLY
PROCEDURE
1. REMOVE BRAKE ACTUATOR BRACKET NO. 1
(a) Using a hexagon wrench (5 mm), remove the screw and brake actuator bracket No. 1.
|
(b) Using a screwdriver, remove the fluid level warning switch connector. |
|
2. REMOVE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY
(a) Remove the screw from the master cylinder reservoir.
|
(b) Using a pin punch and hammer, remove the pin from the master cylinder reservoir. |
|
(c) Pull out the master cylinder reservoir.
(d) Remove the 3 grommets.
(e) Remove the cap.
3. REMOVE BRAKE ACTUATOR HOSE NO. 1
(a) Using needle-nose pliers, slide the 2 clips.
(b) Remove the brake actuator hose.
4. REMOVE BRAKE ACTUATOR TUBE NO. 1
(a) Using a union nut wrench, remove the brake actuator tube No. 1.
5. REMOVE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY
(a) Using a screwdriver, remove the 2 plugs.
|
(b) Remove the 2 screws and pull the wire harness. |
|
|
(c) Using a screwdriver, remove the clip. |
|
|
(d) Remove the brake booster w/ accumulator pump assembly. |
|
|
(e) Using a hexagon wrench (4 mm), remove the 2 pins. |
|
(f) Remove the 2 bushes and 2 collars from the brake booster with accumulator pump assembly.
6. REMOVE BRAKE ACTUATOR BRACKET
(a) Using a hexagon wrench (5 mm), remove the screw and brake actuator bracket.
7. REMOVE BRAKE BOOSTER PUMP BRACKET
(a) Using a hexagon wrench (5 mm), remove the 2 screws and brake booster pump bracket.
(b) Remove the bush from the brake booster pump bracket.
8. REMOVE MASTER CYLINDER PUSH ROD CLEVIS
(a) Loosen the lock nut on the brake master cylinder side, and then remove the rod operating adapter and lock nut.
(b) Loosen the lock nut on the rod operating adapter, and then remove the push rod clevis and lock nut.
9. REMOVE MASTER CYLINDER BOOT
10. REMOVE PISTON
(a) Which pressing in the piston with a screwdriver, use a pin or equivalent to push the C-ring from the hole in the master cylinder body. Then remove the snap ring with another screwdriver.
(b) Remove the piston by pulling it straight out, not at an angle.
NOTICE:
- If the piston is pulled out at an angle, there is a possibility that the cylinder bore could be damaged.
- Be careful not to damage the rubber lips on the piston when reassembling.
11. REMOVE MASTER CYLINDER SOLENOID
(a) Remove the 6 bolts.
(b) Remove the master cylinder solenoid and the gasket.
12. REMOVE BRAKE BOOSTER ACCUMULATOR ASSEMBLY
(a) Place the brake booster with accumulator pump assembly in a vise with a cloth.
(b) Using a socket wrench (17 mm), remove the brake booster accumulator.
(c) Remove the brake booster accumulator pipe, compression spring and O-ring.
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT BRAKE MASTER CYLINDER FLUID PRESSURE CHANGE
(a) Inspect the battery positive voltage.
Battery positive voltage:
10 to 14 V
(b) Turn the ignition switc ...
Removal
REMOVAL
CAUTION / NOTICE / HINT
NOTICE:
Before starting the work, make sure that the ignition switch is off
and depress the brake pedal more than 20 times.
As high pressure is appli ...
Other materials:
Front passenger occupant classification system
Your vehicle is equipped with a front passenger occupant classification system.
This system detects the conditions of the right front passenger seat and activates
or deactivates the devices for the front passenger.
1. SRS warning light
2. Front passenger’s seat belt reminder light
3. AIR ...
Reassembly
REASSEMBLY
PROCEDURE
1. INSTALL BRAKE BOOSTER ACCUMULATOR ASSEMBLY
(a) Place the brake booster pump in a vise with a cloth.
(b) Install the brake booster accumulator pipe, compression spring and a new
O-ring.
NOTICE:
Ensure that no foreign matter enters the pump.
(c) Using a socket wrench ...
Maintenance requirements
To ensure safe and economical driving, day-to-day care and regular maintenance
is essential. It is the owner’s responsibility to perform regular checks. Toyota
recommends the following maintenance.
■ General maintenance
Should be performed on a daily basis. This can be done by yourself ...
