Toyota Tacoma (2015-2018) Service Manual: Traffic Information is not Displayed

Toyota Tacoma (2015-2018) Service Manual / Navigation / Multi Info Display / Navigation System / Traffic Information is not Displayed

CAUTION / NOTICE / HINT

NOTICE:

Traffic information requires payment. An "XM Nav Traffic" contract must be made between the satellite radio company and the user. If the contract expires, traffic information will not be available.
Traffic information does not apply to all roads, only main roads. For the latest information on coverage areas, contact the satellite radio company.

PROCEDURE

1.	CHECK DISPLAY

(a) Check which communication is not being used for displaying traffic information.

HINT:

Display of traffic information received via HD traffic is given priority while in an HD radio service area.

Result

Result	Proceed to
Traffic information using HD radio communication is not displayed	A
Traffic information using Entune function communication is not displayed	B

GO TO STEP 3

2.	CHECK SYMPTOMS

(a) Check for symptoms (poor sound quality, sounds cannot be heard, etc.) during conventional FM radio broadcasting.

Result

Result	Proceed to
Symptoms occur	A
Symptoms do not occur	B

GO TO "RADIO BROADCAST CANNOT BE RECEIVED OR POOR RECEPTION" IN PROBLEM SYMPTOMS TABLE

GO TO STEP 5

3.	CHECK SYMPTOMS

(a) Check for symptoms (cellular phone cannot be registered, applications cannot be started, etc.) with an ordinary Entune function.

Result

Result	Proceed to
Symptoms occur	A
Symptoms do not occur	B

GO TO "ENTUNE FUNCTION" IN PROBLEM SYMPTOMS TABLE

4.	CHECK SETTINGS

(a) Check if the navigation system is set to receive traffic information using Entune function communication as well as HD radio communication.

OK:

The navigation system is set to use Entune function communication.

END

5.	CHECK SETTINGS OF TRAFFIC INFORMATION

(a) Check if the display setting of traffic information on the navigation screen is on.

OK:

The display setting of traffic information is on.

END

6.	CHECK COVERAGE AREA

(a) Check that the current position of the vehicle is within the HD traffic or Entune function coverage area.

OK:

Vehicle is within coverage area.

MOVE TO WITHIN COVERAGE AREA (FOR LATEST COVERAGE AREA, CONFIRM WITH RADIO STATION)

7.	CHECK SCALE OF MAP DISPLAY

(a) Check if the traffic information that is currently not displayed can be displayed at the scale shown in the table below.

Traffic Information to be Displayed	Display Scale
Traffic information list	1:1280000 or below
Traffic information icon (Closed Road, Accidents, Danger, Road Conditions, Road Works, Weather)	1:640000 or below
Traffic information icon (Stationary Traffic Jam, Delays, Parking, Other)	1:80000 or below

OK:

Traffic information can be displayed.

END

REPLACE NAVIGATION RECEIVER ASSEMBLY

Satellite Radio Broadcast cannot be Selected or After Selecting Broadcast, Broadcast cannot be Added into Memory

CAUTION / NOTICE / HINT NOTICE: Some satellite radio broadcasts require payment. A contract must be made between a satellite radio company and the user. If the contract expires, it will not be p ...

Noise Occurs

PROCEDURE 1. NOISE CONDITION (a) Check from which direction the noise comes (front left or right, or rear left or right). OK: The location of the noise source ca ...

Other materials:

Rear Door Black Out Tape
Components COMPONENTS ILLUSTRATION Installation INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH and LH sides. The procedure described below is for the LH side. PROCEDURE 1. REPAIR INSTRUCTION 2. INSTALL NO. 2 BLACK OUT TAPE (a) Refer ...

Inspection
INSPECTION PROCEDURE 1. INSPECT OIL CLEARANCE (a) Using a micrometer and caliper gauge, measure the oil seal clearance. Standard clearance: 0.021 to 0.043 mm (0.0008 to 0.0017 in.) Maximum clearance: 0.07 mm (0.0028 in.) If it is greater than the maximum, replace the vane pump assembly. ...

TC and CG Terminal Circuit
DESCRIPTION DTC output mode is set by connecting terminals TC and CG of the DLC3. The DTCs are displayed by blinking the SRS warning light. HINT: Make sure that DTCs which relate to the CAN communication system are not output. If any of these DTCs are output, check the CAN communicat ...