Toyota Tacoma (2015-2018) Service Manual: System Description
SYSTEM DESCRIPTION
1. GENERAL
This system has the following functions: manual slide open and close; auto slide open and close; manual tilt up and down; auto tilt up and down; jam protection; key off operation; key-linked open and close; wireless transmitter-linked open sliding roof open warning.
2. FUNCTION OF MAIN COMPONENTS
|
Component |
Outline |
|---|---|
|
Sliding roof ECU (Sliding roof drive gear sub-assembly) |
The sliding roof ECU (sliding roof drive gear sub-assembly) controls the rotational direction of the motor, which tilts or slides the sliding roof glass. |
|
Sliding roof switch (Roof console box assembly) |
The sliding roof switch (roof console box assembly) outputs operation signals to the sliding roof ECU (sliding roof drive gear sub-assembly). |
3. SYSTEM OPERATION
The sliding roof has the following features.
|
Function |
Outline |
|---|---|
|
Manual slide open and close |
This function causes the sliding roof to open (or close) when the OPEN switch (or CLOSE switch) is pressed for a maximum of 0.3 seconds. The sliding roof stops as soon as the switch is released. |
|
Auto slide open and close*1, *2 |
This function causes the sliding roof to reach the comfort stop position or fully open (or fully close) when the OPEN switch (or CLOSE switch) is pressed for a minimum of 0.3 seconds. |
|
Manual tilt up and down |
This function causes the sliding roof to tilt up (or tilt down) when the UP switch (or DOWN switch ) is pressed for a maximum of 0.3 seconds. The sliding roof stops as soon as switch is released. |
|
Auto tilt up and down*1, *2 |
This function causes the sliding roof to fully tilt up (or tilt down) when the UP switch (or DOWN switch) is pressed for a minimum of 0.3 seconds. |
|
Jam protection*2 |
The jam protection function automatically stops the sliding roof and moves it open halfway (or fully tilt up) if a foreign object gets jammed in the sliding roof during close or tilt down operation. |
|
Key-off operation*2 |
The key-off operation function makes it possible to operate the sliding roof for approximately 43 seconds after the ignition switch is turned to ACC or off, if the front doors are not opened. |
|
Key-linked open and close*2, *3 |
HINT: This function is linked with the power window key-linked function. |
|
Wireless transmitter-linked open,*2, *3 |
When the main body ECU (multiplex network body ECU) receives an unlock signal from the transmitter continuously for longer than 4 seconds, the sliding roof ECU (sliding roof drive gear sub-assembly) activates the sliding roof motor to open the sliding roof while the transmitter switch pressed. HINT: This function is linked with the power window wireless transmitter-linked function. |
|
Sliding roof open warning*1, *2 |
When the ignition switch is turned from ON to off and the driver door is opened with the sliding roof open, the buzzer in the combination meter assembly sounds once. Then, a warning message appears on the multi-information display.*4 |
- *1: This function can be customized (See page
.gif)
). If the customize setting is OFF, this
function does not operate. - *2: If the sliding roof ECU (sliding roof drive gear sub-assembly) has not been initialized, this function does not operate.
- *3: This function is set through the customize function, as it is off by default.
- *4: w/ Multi-information Display
Parts Location
PARTS LOCATION
ILLUSTRATION
...
System Diagram
SYSTEM DIAGRAM
...
Other materials:
Communication Error from ECM to VSC Invalid Serial Data Received (P163181)
DESCRIPTION
The ECM sends signals such as dynamic radar cruise control operation signals,
brake operation demand signals and buzzer operation demand signals to the skid control
ECU (master cylinder solenoid)*1 or skid control ECU (brake actuator assembly)*2
when the dynamic radar cruise contr ...
Data Signal Circuit between Radio Receiver and Stereo Jack Adapter
DESCRIPTION
The No. 1 stereo jack adapter assembly sends the sound data signal or image data
signal from a USB device to the radio and display receiver assembly via this circuit.
WIRING DIAGRAM
PROCEDURE
1.
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMB ...
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of problem symptoms.
If multiple suspected areas are listed, the potential causes of the symptoms
are listed in order of probability in the "Suspected Area" column of the
table. Check each sy ...
