DESCRIPTION
The skid control ECU (master cylinder solenoid) is connected to the combination meter via CAN communication.
The combination meter has a built-in VSC warning buzzer:
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
When replacing the skid control ECU (master cylinder solenoid), perform the zero point calibration (See page ).
PROCEDURE
1. |
CHECK CAN COMMUNICATION SYSTEM |
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (See page ).
OK:
CAN Bus Check indicates no malfunctions in CAN communication.
NG |
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) |
|
2. |
PERFORM ACTIVE TEST USING TECHSTREAM (BUZZER) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.
(e) According to the display on the tester, perform the Active Test.
ABS/VSC/TRAC
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
---|---|---|---|
Buzzer |
VSC warning buzzer |
Buzzer OFF/ON |
The buzzer can be heard |
(f) Check that the buzzer sounds or stops in accordance with the Techstream.
Result
Result |
Proceed to |
---|---|
Buzzer does not sound or stop |
A |
Buzzer sounds and stops |
B |
B |
USE SIMULATION METHOD TO CHECK |
|
3. |
REPLACE COMBINATION METER ASSEMBLY |
(a) Turn the ignition switch off.
(b) Replace the combination meter (See page ).
|
4. |
PERFORM ACTIVE TEST USING TECHSTREAM (BUZZER) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.
(e) According to the display on the tester, perform the Active Test.
ABS/VSC/TRAC
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
---|---|---|---|
Buzzer |
VSC warning buzzer |
Buzzer OFF/ON |
The buzzer can be heard |
(f) Check that the buzzer sounds or stops in accordance with the Techstream.
Result
Result |
Proceed to |
---|---|
Buzzer does not sound or stop |
A |
Buzzer sounds and stops |
B |
A |
REPLACE MASTER CYLINDER SOLENOID |
B |
END |
Dtc Check / Clear
DTC CHECK / CLEAR
1. CHECK DTC (CHECK USING TECHSTREAM)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Navigation System / Trouble
Codes.
(e) Check for DTCs, and then write them down.
( ...
Terminals Of Ecu
TERMINALS OF ECU
Text in Illustration
*a
Component without harness connected
(Skid Control ECU [Brake Actuator Assembly])
-
-
Terminal No. (Symbol)
Terminal Description
1 (GND2)
Pump motor g ...
Meter Illumination does not Dim at Night
DESCRIPTION
In this circuit, the combination meter assembly auto dimmer signals from the
main body ECU using the CAN communication system (CAN V1 Bus). When the combination
meter assembly an auto dimmer signal, it dims the meter illumination (warning and
indicator lights). The main body ECU ( ...