DESCRIPTION
The combination meter assembly receives the turn signal switch information and controls the turn signal lights.
WIRING DIAGRAM
PROCEDURE
1. |
READ VALUE USING TECHSTREAM (TURN SIGNAL SWITCH) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Combination Meter / Data List.
(e) According to the display on the Techstream, read the Data List.
Combination Meter
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
---|---|---|---|
Turn Signal Switch (Right) |
Turn signal switch (right) signal / ON or OFF |
ON: Turn signal switch (right) on OFF: Turn signal switch (right) off |
- |
Turn Signal Switch (Left) |
Turn signal switch (left) signal / ON or OFF |
ON: Turn signal switch (left) on OFF: Turn signal switch (left) off |
- |
Turn Switch Signal (Full Turn) |
Turn signal switch (full turn) signal / ON or OFF |
ON: Turn signal switch (left or right) on OFF: Turn signal switch (left and right) off |
- |
OK:
Normal conditions listed above are displayed.
OK |
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
2. |
INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY |
(a) Remove the C11 headlight dimmer switch assembly. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
12 (TR) - 15 (EL) |
Turn signal switch in neutral position |
10 kΩ or higher |
11 (TL) - 15 (EL) |
Turn signal switch in neutral position |
10 kΩ or higher |
13 (CR) - 15 (EL) |
Turn signal switch in neutral position |
10 kΩ or higher |
12 (TR) - 15 (EL) |
Turn signal switch in right turn position |
Below 1 Ω |
13 (CR) - 15 (EL) |
Turn signal switch in full right turn position |
Below 1 Ω |
11 (TL) - 15 (EL) |
Turn signal switch in left turn position |
Below 1 Ω |
13 (CR) - 15 (EL) |
Turn signal switch in full left turn position |
Below 1 Ω |
*1 |
Component without harness connected (Headlight Dimmer Switch Assembly) |
NG |
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY |
|
3. |
CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - COMBINATION METERASSEMBLY AND BODY GROUND) |
(a) Disconnect the C9 combination meter assembly connector.
(b) Disconnect the C11 headlight dimmer switch assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
C11-12 (TR) - C9-8 (ER) |
Always |
Below 1 Ω |
C11-11 (TL) - C9-7 (EL) |
Always |
Below 1 Ω |
C11-13 (CR) - C9-9 (SW) |
Always |
Below 1 Ω |
C11-12 (TR) - Body ground |
Always |
10 kΩ or higher |
C11-11 (TL) - Body ground |
Always |
10 kΩ or higher |
C11-13 (CR) - Body ground |
Always |
10 kΩ or higher |
C11-15 (EL) - Body ground |
Always |
Below 1 Ω |
OK |
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
Transmission Fluid Temperature Sensor "A" Circuit Low Input (P0712,P0713)
DESCRIPTION
The No. 1 ATF temperature sensor converts the fluid temperature into a resistance
value for use by the ECM.
The ECM applies a voltage to the temperature sensor through terminal THO1 of
the ECM.
The sensor resistance changes with the ATF temperature. As the temperature becomes
hi ...
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
Power Window Control System
DTC Code
Detection Item
See page
B2311
Power Window Motor Malfunction
B2312
Power Window Switch Malfunction
...
Clutch Master Cylinder
Components
COMPONENTS
ILLUSTRATION
Installation
INSTALLATION
PROCEDURE
1. INSTALL CLUTCH MASTER CYLINDER ASSEMBLY
(a) Install the clutch master cylinder assembly to the clutch pedal support with
the 2 bolts.
Torque:
12 N·m {120 kgf·cm, 9 ft·lbf}
(b) Install the clutch start swi ...