Toyota Tacoma (2015-2018) Service Manual: TRAC OFF Indicator Light Remains ON

Toyota Tacoma (2015-2018) Service Manual / Brake Control / Dynamic Control Systems / Vehicle Stability Control System(for Hydraulic Brake Booster) / TRAC OFF Indicator Light Remains ON

DESCRIPTION

In 2WD mode:
Operation of the VSC OFF switch changes the vehicle between normal mode, TRAC OFF mode (AUTO LSD mode) and VSC OFF mode. During normal mode, pressing the VSC OFF switch for a short amount of time changes the vehicle to TRAC OFF mode (AUTO LSD mode), TRAC operation is prohibited, and the VSC OFF and AUTO LSD indicator lights turns on. However, if the vehicle speed exceeds 50 km/h, the indicator lights turns off.

When the vehicle is stopped, pressing the VSC OFF switch for 3 seconds or more changes the vehicle to VSC OFF mode, TRAC and VSC operation are prohibited, and the TRAC OFF indicator and VSC OFF indicator lights turn on.
In 4WD mode:
Operation of the VSC OFF switch changes the vehicle between normal mode and VSC OFF mode. During normal mode, when the vehicle is stopped, pressing the VSC OFF switch for 3 seconds or more changes the vehicle to VSC OFF mode, TRAC and VSC operation are prohibited, and the TRAC OFF indicator and VSC OFF indicator lights turn on.
- When the transfer is in L4, VSC is prohibited and the TRAC OFF indicator and VSC OFF indicator lights turn on.
- When the rear differential is locked, VSC is prohibited and the TRAC OFF indicator and VSC OFF indicator lights turn on. At this time, ABS is also prohibited and the ABS warning light turns on.
Fail Safe
- When the temperature inside the hydraulic brake booster becomes too high, the TRAC OFF indicator light turns on and traction control is stopped until the temperature decreases.
- If there is a malfunction in the SFI system, the TRAC system will be prohibited and the TRAC OFF indicator will turn on.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (master cylinder solenoid), perform calibration (See page ).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
As there may be malfunctions in the transfer system related to when the transfer operates in L4, check the transfer system first.

PROCEDURE

1.	CHECK SFI SYSTEM

(a) Check if SFI system DTCs are output (See page Result ).

Result

Result	Proceed to
DTCs are not output	A
DTCs are output	B

GO TO SFI SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

2.	CHECK CAN COMMUNICATION SYSTEM

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(d) Turn the Techstream on.

(e) Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (See page OK: OK: ).

OK:

CAN Bus Check indicates no malfunctions in CAN communication.

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

3.	INSPECT SKID CONTROL ECU (CSW TERMINAL)

(a) Disconnect the S1 skid control ECU (master cylinder solenoid) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Switch Condition	Specified Condition
S1-9 (CSW) - Body ground	VSC OFF switch not pushed in	10 kΩ or higher
S1-9 (CSW) - Body ground	VSC OFF switch pushed in	Below 1 Ω

Text in Illustration

*a	Front view of wire harness connector (to Skid Control ECU)

Result

Result	Proceed to
OK (w/ Rear Differential Lock)	A
OK (w/o Rear Differential Lock)	B
NG	C

GO TO STEP 5

GO TO STEP 6

4.	CHECK FOR DIFFERENTIAL SYSTEM

(a) Reconnect the S1 skid control ECU (master cylinder solenoid) connector.

(b) Connect the Techstream to the DLC3.

(d) Turn the Techstream on.

(e) Enter the following menus: Powertrain / Four Wheel Drive / Trouble Codes.

(f) Check for DTCs.

Result

Result	Proceed to
DTCs are not output	A
DTCs are output	B

GO TO DIFFERENTIAL SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

5.	READ VALUE USING TECHSTREAM (TRAC/VSC OFF MODE)

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(d) Turn the Techstream on.

(e) Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

ABS/VSC/TRAC

Tester Display	Test Part	Control Range	Diagnostic Note
TRAC/VSC Off Mode	TRAC/VSC off mode/ Normal, TRC OFF, Unknown or VSC OFF	Normal: Normal mode TRC OFF: TRAC OFF mode VSC OFF: VSC OFF mode	-

Tester Display

Test Part

Control Range

Diagnostic Note

TRAC/VSC Off Mode

TRAC/VSC off mode/ Normal, TRC OFF, Unknown or VSC OFF

Normal: Normal mode

TRC OFF: TRAC OFF mode

VSC OFF: VSC OFF mode

(f) Check that the mode display changes according to VSC OFF switch operation.

OK:

Display changes according to switch operation.

GO TO METER / GAUGE SYSTEM

REPLACE MASTER CYLINDER SOLENOID

6.	INSPECT VSC OFF SWITCH

(a) Remove the VSC OFF switch (See page (b) Inspect the VSC OFF switch (See page ). ).

(b) Inspect the VSC OFF switch (See page ).

REPLACE VSC OFF SWITCH

7.	INSPECT ROOF CONSOLE BOX ASSEMBLY

(a) Remove the roof console box assembly.

for Double Cab: (See page )
for Access Cab: (See page )

Text in Illustration

Component without harness connected

(Roof Console Box Assembly)

(b) Measure the resistance according the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
R44-16 (+) - 9	Always	Below 1 Ω
R44-12 (GND) - 6 (E)	Always	Below 1 Ω

Result

Result	Proceed to
OK	A
NG (for Double Cab)	B
NG (for Access Cab)	C

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASTER CYLINDER SOLENOID - ROOF CONSOLE BOX ASSEMBLY)

REPLACE ROOF CONSOLE BOX ASSEMBLY

TRAC OFF Indicator Light does not Come ON

DESCRIPTION Refer to TRAC OFF Indicator Light Remains ON (See page ). WIRING DIAGRAM Refer to TRAC OFF Indicator Light Remains ON (See page ). CAUTION / NOTICE / HINT NOTICE: When re ...

VSC OFF Indicator Light Remains ON

DESCRIPTION In 2WD mode: Operation of the VSC OFF switch changes the vehicle between normal mode, TRAC OFF mode (AUTO LSD mode) and VSC OFF mode. During normal mode, pressing the VS ...

Other materials:

Precaution
PRECAUTION 1. BASIC REPAIR HINT (a) HINTS ON OPERATIONS 1 Attire Always wear a clean uniform. A hat and safety shoes must be worn. 2 Vehicle protection Prepare a grille cover, fe ...

Terminals Of Ecu
TERMINALS OF ECU 1. CHECK 4 WHEEL DRIVE CONTROL ECU Text in Illustration *a Component with harness connected (4 Wheel Drive Control ECU) - - (a) Measure the resistance and voltage according to the value(s) in the table below. ...

Installation
INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for both the LH and RH sides. The procedure described below is for the LH side. PROCEDURE 1. INSTALL HEADLIGHT ASSEMBLY (a) Connect the connectors. (b) Engage the clamp to install the headlight assembly. (c) ...