Toyota Tacoma (2015-2018) Service Manual: Tire Pressure Monitor ECU Communication Stop Mode

Toyota Tacoma (2015-2018) Service Manual / Can Communication / Can Communication System / Tire Pressure Monitor ECU Communication Stop Mode

DESCRIPTION

Detection Item	Symptom	Trouble Area
Tire Pressure Monitor ECU Communication Stop Mode	Either condition is met: Communication stop for "Tire Pressure2" is indicated on the "Communication Bus Check" screen of the Techstream. Click here Communication system DTCs (DTCs that start with U) that correspond to "Tire Pressure Monitor ECU Communication Stop Mode" in "DTC Combination Table" are output. Click here	Door control and tire pressure monitoring system receiver assembly branch line or connector Power source circuit of door control and tire pressure monitoring system receiver assembly Door control and tire pressure monitoring system receiver assembly ground circuit Door control and tire pressure monitoring system receiver assembly

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

NOTICE:

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click here
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
Some parts must be initialized and set when replacing or removing and installing parts.
Click here
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click here
Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

1.	CHECK FOR OPEN IN CAN BUS LINES (DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY BRANCH LINE)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the door control and tire pressure monitoring system receiver assembly connector.

Standard Resistance:

Tester Connection	Condition	Specified Condition
T24-9 (CANH) - T24-10 (CANL)	Cable disconnected from negative (-) battery terminal	54 to 69 Ω

Text in Illustration

*a	Front view of wire harness connector (to Door Control and Tire Pressure Monitoring System Receiver Assembly)

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY)

2.	CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
T24-12 (GND) - Body ground	Cable disconnected from negative (-) battery terminal	Below 1 Ω

(b) Connect the cable to the negative (-) battery terminal.

Standard Voltage:

Tester Connection	Switch Condition	Specified Condition
T24-7 (+B) - Body ground	Always	11 to 14 V
T24-1 (IG) - Body ground	Ignition switch ON	11 to 14 V

Text in Illustration

*a	Front view of wire harness connector (to Door Control and Tire Pressure Monitoring System Receiver Assembly)

REPLACE DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

Front Camera Module Communication Stop Mode

DESCRIPTION Detection Item Symptom Trouble Area Front Camera Module Communication Stop Mode Either Condition is met: Communi ...

Network Gateway Ecu

Components COMPONENTS ILLUSTRATION Installation INSTALLATION PROCEDURE 1. INSTALL NETWORK GATEWAY ECU (a) Install the network gateway ECU with the bolt. Torque: 3.0 N·m {31 kgf·cm, 2 ...

Other materials:

Skid Control Buzzer Circuit (C1A4A)
DESCRIPTION Based on dynamic radar cruise control system operation, the forward recognition camera provides warnings to the driver by sounding the skid control buzzer. DTC C1A4A is stored when a malfunction is detected in the skid control buzzer circuit. DTC No. Detectio ...

Engine compartment
2.7 L 4-cylinder (2TR-FE) engine 1. Washer fluid tank 2.Radiator cap 3.Engine coolant reservoir 4. Engine oil filler cap 5. Power steering fluid reservoir 6. Engine oil level dipstick 7. Brake fluid reservoir 8. Fuse box 9. Battery 10. Condenser 11. Radiator 4.0 L V6 (1GR-FE) engine ...

Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE FRONT LICENSE PLATE BRACKET (a) Remove the 2 screws and front license plate bracket. 2. REMOVE NO. 4 ENGINE ROOM WIRE (w/ Fog Light) (a) Disconnect the 2 connectors. ...