Toyota Tacoma manuals

Toyota Tacoma (2005–2015) Owners Manual: Tire inflation pressure

■ Tire inflation pressure

The recommended cold tire inflation pressure and tire size is displayed on the tire and loading information label.

Regular Cab and Double Cab models

Access Cab models

Access Cab models

■ Inspection and adjustment procedure

■ Inspection and adjustment procedure

1. Tire valve

1. Tire valve

2. Tire pressure gauge

Press the tip of the tire pressure Remove the tire valve cap.

gauge onto the tire valve.Press the tip of the tire pressure gauge onto the tire valve.

of the gauge. Read the pressure using the graduations of the gauge.

not within the recommended levels, adjust inflate the tire. If the tire inflation pressure is not within the recommended levels, adjust inflate the tire.

If you add too much air, press the center of the valve to lower.

pressure measurement and adjustment, apply soapy water to the valve and check for After completing the tire inflation pressure measurement and adjustment, apply soapy water to the valve and check for leakage.

■Tire inflation pressure check interval Reinstall the tire valve cap.

■Tire inflation pressure check interval

You should check tire pressure every two weeks, or at least once a month.

Do not forget to check the spare.

■Effects of incorrect tire inflation pressure

Driving with incorrect tire inflation pressure may result in the following: ●Reduced fuel efficiency

●Reduced driving comfort and tire life

●Reduced safety

●Damage to the drive train

If a tire needs frequent refilling, have it checked by your Toyota dealer.

■Instructions for checking tire inflation pressure

When checking tire inflation pressure, observe the following: ●Check only when the tires are cold.

If your vehicle has been parked for at least 3 hours and has not been driven for more than 1 mile or 1.5 km, you will get an accurate cold tire inflation pressure reading.

●Always use a tire pressure gauge.

The appearance of the tire can be misleading. In addition, tire inflation pressures that are even just a few pounds off can degrade ride and handling.

●Do not bleed or reduce tire inflation pressure after driving. It is normal for the tire inflation pressure to be higher after driving.

●Never exceed the vehicle capacity weight.

Passengers and luggage weight should be placed so that the vehicle is balanced.

CAUTION

■Proper inflation is critical to save tire performance

Keep your tires properly inflated.

Otherwise, the following conditions may occur and result in an accident causing death or serious injury.

●Excessive wear

●Uneven wear

●Poor handling

●Possibility of blowouts resulting from overheated tires

●Poor sealing of the tire bead

●Wheel deformation and/or tire separation

●A greater possibility of tire damage from road hazards

NOTICE

■When inspecting and adjusting tire inflation pressure

Be sure to reinstall the tire valve caps.

Without the valve caps, dirt or moisture could get into the valve and cause air leakage, which could result in an accident. If the caps have been lost, replace them as soon as possible.

Tires
Replace or rotate tires in accordance with maintenance schedules and treadwear. ■ Checking tire 1. New tread 2. Treadwear indicator 3. Worn tread The location of treadwear indicators is s ...

Wheels
If a wheel is bent, cracked or heavily corroded, it should be replaced. Otherwise, the tire may separate from the wheel or cause loss of handling control. ■ Wheel selection When replacing whe ...

Other materials:

Inspection
INSPECTION PROCEDURE 1. INSPECT TRANSMISSION FLOOR SHIFT ASSEMBLY (w/o Smart Key System) HINT: If the results of the following inspections are as specified but a malfunction has occurred, replace the transmission floor shift assembly. (a) Inspect the wire harness. (1) Disconnect the shift lo ...

Power Outlet Socket(for Rear Side)
Components COMPONENTS ILLUSTRATION *1 USB CHARGER SOCKET - - Removal REMOVAL PROCEDURE 1. REMOVE REAR CONSOLE BOX ASSEMBLY Click here 2. REMOVE USB CHARGER SOCKET (a) Disengage the 4 claws to remove the USB charger soc ...

Open in Stop Light Switch Circuit (C1425)
DESCRIPTION The skid control ECU (master cylinder solenoid) inputs stop light switch signals and the brake operation condition. The skid control ECU (master cylinder solenoid) has an open detection circuit, which outputs this DTC when detecting an open circuit in the stop light input line or ...

© 2011-2024 Copyright www.ttguide.net