TERMINALS OF ECU
1. CHECK DRIVER SIDE JUNCTION BLOCK AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
(a) Disconnect the MB main body ECU (multiplex network body ECU) connectors.
(b) Measure the voltage and resistance according to the value(s) in the table below.
HINT:
Measure the values on the wire harness side with the connectors disconnected.
Tester Connection |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
---|---|---|---|---|
MB-11(GND1) - Body ground |
- |
Ground |
Always |
Below 1 Ω |
MB-31 (BECU) - Body ground |
- |
Battery power supply |
Always |
11 to 14 V |
MB-30 (ACC) - Body ground |
- |
ACC power supply |
Ignition switch ACC |
11 to 14 V |
MB-30 (ACC) - Body ground |
- |
ACC power supply |
Ignition switch off |
Below 1 V |
MB-32 (IG) - Body ground |
- |
IG power supply |
Ignition switch ON |
11 to 14 V |
MB-32 (IG) - Body ground |
- |
IG power supply |
Ignition switch off |
Below 1 V |
If the result is not as specified, there may be a malfunction in the wire harness.
(c) Reconnect the MB main body ECU (multiplex network body ECU) connectors.
(d) Measure the voltage and check for pulses according to the value(s) in the table below.
Tester Connection |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
---|---|---|---|---|
1H-10 (ACT-) - Body ground |
LA-G - Body ground |
Door lock motor unlock drive output (except driver door) |
Door control switch or driver door key cylinder off |
Below 1 V |
Door control switch or driver door key cylinder unlocked |
11 to 14 V |
|||
1D-3 (ACT-) - Body ground |
G - Body ground |
Door lock motor unlock drive output (except driver door) |
Door control switch or driver door key cylinder off |
Below 1 V |
Door control switch or driver door key cylinder unlocked |
11 to 14 V |
|||
1D-1 (ACT+) - Body ground |
R - Body ground |
Door lock motor lock drive output (all doors) |
Door control switch or driver door key cylinder off |
Below 1 V |
Door control switch or driver door key cylinder locked |
11 to 14 V |
|||
1H-12 (ACT+) - Body ground |
LA-R - Body ground |
Door lock motor lock drive output (all doors) |
Door control switch or driver door key cylinder off |
Below 1 V |
Door control switch or driver door key cylinder locked |
11 to 14 V |
|||
1D-2 (ACTD) - Body ground |
B - Body ground |
Driver door lock motor unlock drive output |
Door control switch or driver door key cylinder off |
Below 1 V |
Door control switch or driver door key cylinder unlocked |
11 to 14 V |
|||
M6-2 (UL3) - Body ground |
G - Body ground |
Driver door key-linked unlock input |
Driver door key cylinder turned to neutral position → on (unlock) |
Pulse generation → Below 1 V |
M6-29 (L2) - Body ground |
SB - Body ground |
Driver door key-linked lock input |
Driver door key cylinder turned to neutral position → on (lock) |
Pulse generation → Below 1 V |
M6-27 (FRCY) - Body ground |
LG - Body ground |
Front door courtesy light switch RH input |
Front door RH open |
Below 1 V |
M6-27 (FRCY) - Body ground |
LG - Body ground |
Front door courtesy light switch RH input |
Front door RH open |
11 to 14 V |
M6-6 (FLCY) - Body ground |
Y - Body ground |
Front door courtesy light switch LH input |
Front door LH open |
Below 1 V |
M6-6 (FLCY) - Body ground |
Y - Body ground |
Front door courtesy light switch LH input |
Front door LH closed |
11 to 14 V |
1H-36 (LCTY) - Body ground |
P - Body ground |
Rear door courtesy light switch LH input*1 Upper access panel lock assembly LH input*2 Lower access panel lock assembly LH input*2 |
Rear door LH open |
Below 1 V |
1H-36 (LCTY) - Body ground |
P - Body ground |
Rear door courtesy light switch LH input*1 Upper access panel lock assembly LH input*2 Lower access panel lock assembly LH input*2 |
Rear door LH closed |
Pulse generation |
1D-30 (RCTY) - Body ground |
V - Body ground |
Rear door courtesy light switch RH input*1 Upper access panel lock assembly RH input*2 Lower access panel lock assembly RH input*2 |
Rear door RH open |
Below 1 V |
1D-30 (RCTY) - Body ground |
V - Body ground |
Rear door courtesy light switch RH input*1 Upper access panel lock assembly RH input*2 Lower access panel lock assembly RH input*2 |
Rear door RH closed |
Pulse generation |
1D-11 (LSFL) - Body ground |
P - Body ground |
Front door LH unlock detection switch input |
Front door LH unlocked |
Below 1 V |
1D-11 (LSFL) - Body ground |
P - Body ground |
Front door LH unlock detection switch input |
Ignition switch off, all doors closed and front door LH locked |
Pulse generation |
1D-24 (LSFR) - Body ground |
GR - Body ground |
Front door RH unlock detection switch input |
Front door RH unlocked |
Below 1 V |
1D-24 (LSFR) - Body ground |
GR - Body ground |
Front door RH unlock detection switch input |
Ignition switch off, all doors closed and front door RH locked |
Pulse generation |
1A-41 (LSR) - Body ground |
Y - Body ground |
Rear door RH unlock detection switch input |
Rear door RH or LH unlocked |
Below 1 V |
1A-41 (LSR) - Body ground |
Y - Body ground |
Rear door RH unlock detection switch input |
Ignition switch off, all doors closed and rear door RH and LH locked |
Pulse generation |
1H-27 (LSR) - Body ground |
L - Body ground |
Rear door LH unlock detection switch input |
Rear door LH or RH unlocked |
Below 1 V |
1H-27 (LSR) - Body ground |
L - Body ground |
Rear door LH unlock detection switch input |
Ignition switch off, all doors closed and rear door LH and RH locked |
Pulse generation |
1F-29 (BZR) - Body ground |
Y - Body ground |
Wireless door lock buzzer signal |
Wireless door lock buzzer off |
Below 1 V |
1F-29 (BZR) - Body ground |
Y - Body ground |
Wireless door lock buzzer signal |
Wireless door lock buzzer on |
Pulse generation |
31-1D (KSW) - Body ground*5 |
G - Body ground |
Key unlock warning switch input |
Key in ignition key cylinder |
Below 1 V |
No key in ignition key cylinder |
11 to 14 V or Pulse generation |
While Alarm is Armed, Battery is Reconnected but Alarm does not Sound
DESCRIPTION
While the alarm is armed, the EEPROM inside the main body ECU (multiplex network
body ECU) will remember the armed state even if the battery is disconnected, and
the alarm will sound when the battery is reconnected.
If the alarm does not sound when the battery is reconnected, the a ...
Yaw Rate Sensor Malfunction (C1436)
DESCRIPTION
The skid control ECU (master cylinder solenoid) receives signals from the yaw
rate and acceleration (airbag sensor assembly) via the CAN communication system.
The airbag sensor assembly has a built-in yaw rate and acceleration sensor and
detects the vehicle's condition using 2 ...
FCM Destination Information Unmatched (C1AA1)
DESCRIPTION
When the forward recognition camera is replaced with a new one, the new forward
recognition camera attempts to store country specification information received
from the main body ECU (multiplex network body ECU) and ECM. If the country specification
information stored in the forwa ...