Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: System Diagram

SYSTEM DIAGRAM

Communication Table Communication Table

Sender

Receiver

Signal

Line

ECM

Millimeter Wave Radar Sensor Assembly

  • Cruise control operation signal
  • Accelerator pedal idle position signal
  • Accel override operation signal
  • Cruise control speed status signal
  • Approach warning signal
  • Brake signal
  • Cruise control main switch (ON-OFF button) on signal
  • Cruise control mode signal
  • Set vehicle-to-vehicle distance signal
  • Cruise preset vehicle speed signal

CAN

ECM

Skid Control ECU (Master Cylinder Solenoid)*1

Skid Control ECU (Brake Actuator Assembly)*2

  • Cruise control operation signal
  • Accelerator pedal idle position signal
  • Cruise control operation request signal
  • Braking request signal
  • Target acceleration from cruise control system signal

CAN

ECM

Combination Meter Assembly

  • Low speed cancel buzzer request signal
  • Control vehicle speed unit signal
  • Cruise control display ID signal
  • Cruise control vehicle speed signal

CAN

ECM

Forward Recognition Camera

Cruise control operation signal

CAN

Millimeter Wave Radar Sensor Assembly

ECM

  • Cruise control target acceleration signal
  • Cruise control mode signal
  • Target vehicle detection signal
  • Vehicle-to-vehicle distance control switch status signal
  • Detection of dirt adhesion on millimeter wave radar sensor signal
  • Millimeter wave radar sensor malfunction signal
  • Approach warning signal
  • Bad environment detection signal
  • Cruise control target acceleration raw data signal
  • Force request for millimeter wave radar sensor assembly signal
  • Control status of millimeter wave radar sensor assembly signal

CAN

Millimeter Wave Radar Sensor Assembly

Combination Meter Assembly

Millimeter wave radar sensor beam axis deviation signal

CAN

Skid Control ECU (Master Cylinder Solenoid)*1

Skid Control ECU (Brake Actuator Assembly)*2

Millimeter Wave Radar Sensor Assembly

  • Stop light switch status signal
  • Yaw rate sensor zero point signal
  • Yaw rate sensor zero point malfunction signal
  • Under brake control signal

CAN

Skid Control ECU (Master Cylinder Solenoid)*1

Skid Control ECU (Brake Actuator Assembly)*2

ECM

  • Wheel speed signal
  • Under TRAC control signal
  • Under VSC control signal
  • Cruise control cancellation request signal
  • Stop light switch control relay malfunction signal
  • Temporary inhibition of brake control signal
  • Under brake control signal
  • Presumed road slope signal
  • Estimated acceleration signal

CAN

Steering Angle Sensor (Spiral Cable with Sensor Sub-assembly)

Millimeter Wave Radar Sensor Assembly

  • Steering angle sensor malfunction signal
  • Steering angle signal
  • Steering angle sensor zero point signal

CAN

Main Body ECU (Multiplex Network Body ECU)

Millimeter Wave Radar Sensor Assembly

Destination information signal

CAN

Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly)

Millimeter Wave Radar Sensor Assembly

  • Yaw rate sensor signal
  • Yaw rate sensor malfunction signal
  • Yaw rate sensor voltage signal

CAN

  • *1: for Hydraulic Brake Booster
  • *2: for Vacuum Brake Booster
Parts Location
PARTS LOCATION ILLUSTRATION *A for Hydraulic Brake Booster *B for Vacuum Brake Booster *C for Automatic Transmission ...

How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT HINT: Perform the following procedure to troubleshoot the dynamic radar cruise control system. *: Use the Techstream. PROCEDURE 1. ...

Other materials:

LIN Communication Bus Malfunction (B2325)
DESCRIPTION The main body ECU (multiplex network body ECU) monitors communication between all the ECUs connected to the door bus lines. When the main body ECU (multiplex network body ECU) detects errors in communication with all the ECUs connected to the door bus lines at 2.6-second intervals ...

Data List / Active Test
DATA LIST / ACTIVE TEST 1. DATA LIST HINT: Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals ...

IG Power Source Circuit
DESCRIPTION The main power source is supplied to the air conditioning amplifier assembly when the ignition switch is turned to ON. The power is used for operating the air conditioning amplifier assembly, servo motors, etc. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses ...

В© 2011-2024 Copyright www.ttguide.net