Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Steering Angle Sensor Power Source Voltage Malfunction (C1432)

DESCRIPTION

The skid control ECU (brake actuator assembly) outputs this DTC when it receives a sensor power source malfunction signal from the steering angle sensor.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1432

Steering Angle Sensor Power Source Voltage Malfunction

Steering angle sensor power supply malfunction signal is received from steering angle sensor.

  • ECU-B NO. 2 fuse
  • ECU-IG NO. 3 fuse
  • Steering angle sensor (Spiral cable with sensor sub-assembly)
  • Wire harness or connector

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION / NOTICE / HINT

NOTICE:

  • Do not remove the steering angle sensor from the spiral cable with sensor sub-assembly.
  • When replacing the steering angle sensor (spiral cable with sensor sub-assembly), confirm that the replacement part is of the correct specification.
  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:

  • When U0073, U0124 and/or U0126 is output together with C1432, inspect and repair the trouble areas indicated by U0073, U0124 and/or U0126 first (See page When the speed sensor or the yaw rate sensor (airbag sensor assembly) ).
  • When the speed sensor or the yaw rate sensor (airbag sensor assembly) has trouble, DTCs for the steering angle sensor (spiral cable with sensor sub-assembly) may be output even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate sensor (airbag sensor assembly) are output together with DTCs for the steering angle sensor (spiral cable with sensor sub-assembly), inspect and repair the speed sensor and yaw rate sensor (airbag sensor assembly) first, and then inspect and repair the steering angle sensor (spiral cable with sensor sub-assembly).

PROCEDURE

1.

CHECK TERMINAL VOLTAGE (BAT TERMINAL)

(a) Turn the ignition switch off.

(b) Remove the steering wheel and the column cover lower (See page ).

(c) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

(d) Disconnect the S32 steering angle sensor (spiral cable with sensor sub-assembly) connector.

(e) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

S32-5 (BAT) - Body ground

Always

11 to 14 V

Text in Illustration

*a

Front view of wire harness connector

(to Steering Angle Sensor [Spiral Cable with Sensor Sub-assembly])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BAT CIRCUIT)

OK

2.

CHECK TERMINAL VOLTAGE (IG TERMINAL)

(a) Turn the ignition switch to ON.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

S32-4 (IG) - Body ground

Ignition switch ON

11 to 14 V

Text in Illustration

*a

Front view of wire harness connector

(to Steering Angle Sensor [Spiral Cable with Sensor Sub-assembly])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)

OK

3.

CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

(a) Turn the ignition switch off.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

S32-1 (ESS) - Body ground

Always

Below 1 Ω

Text in Illustration

*a

Front view of wire harness connector

(to Steering Angle Sensor [Spiral Cable with Sensor Sub-assembly])

HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page ).

OK

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ESS CIRCUIT)

Motor Circuit Malfunction (C1428)
DESCRIPTION DTC No. Detection Item DTC Detection Condition Trouble Area C1428 Motor Circuit Malfunction With the mot ...

Steering Angle Sensor Internal Circuit (C1433)
DESCRIPTION The skid control ECU (brake actuator assembly) outputs this DTC when it receives an internal malfunction signal from the steering angle sensor. DTC No. Detection ...

Other materials:

Invalid Data Received from Deceleration Sensor (C1442,C1443)
DESCRIPTION The skid control ECU (master cylinder solenoid) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system. The airbag sensor assembly has a built-in yaw rate and acceleration sensor. DTC Code DTC Dete ...

How To Use This Manual
General Information GENERAL INFORMATION 1. GENERAL DESCRIPTION (a) This manual is written in accordance with SAE J2008. (1) Diagnosis (2) Removing / Installing, Replacing, Disassembling / Reassembling, Checking and Adjusting (3) Final Inspection (b) The following procedures are omitted fr ...

Driver Side Door Entry Unlock Function does not Operate
DESCRIPTION If the entry unlock function does not operate for the driver door only, but the entry lock function operates, the request code is being transmitted properly from the driver door. In this case, there may be a problem related to the touch sensor (connection between the certification ...

© 2011-2024 Copyright www.ttguide.net