Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Steering Angle Sensor (C1A47)

DESCRIPTION

The millimeter wave radar sensor assembly receives steering angle information from the steering angle sensor (spiral cable with sensor sub-assembly). If the millimeter wave radar sensor assembly detects a steering angle sensor (spiral cable with sensor sub-assembly) malfunction, DTC C1A47 will be stored.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1A47

Steering Angle Sensor

While the vehicle is being driven at a speed of 50 km/h (32 mph) or more, the millimeter wave radar sensor assembly receives a steering angle sensor (spiral cable with sensor sub-assembly) malfunction signal continuously for 1 second or more.

  • Vehicle stability control system
  • Millimeter wave radar sensor assembly

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.
  • If the millimeter wave radar sensor assembly has been replaced, be sure to perform millimeter wave radar sensor assembly adjustment.

    Click here

  • The pre-collision system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

    Click here

PROCEDURE

1.

CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)

HINT:

Pre-collision system DTC C1A47 may be stored due to a malfunction in the vehicle stability control system. Therefore, it is necessary to check for and troubleshoot vehicle stability control system DTCs first.

(a) Check for DTCs.

Click here

Result

Proceed to

Vehicle stability control system DTCs are not output

A

Vehicle stability control system DTCs are output

B

B

GO TO VEHICLE STABILITY CONTROL SYSTEM

A

2.

CHECK FOR DTCs (PRE-COLLISION SYSTEM)

(a) Clear the DTCs.

Click here (b) Make sure that the DTC detection conditions are met.

(b) Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

(c) Check for DTCs.

Click here

Result

Proceed to

DTC C1A47 is not output

A

DTC C1A47 is output

B

A

USE SIMULATION METHOD TO CHECK

B

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

Stop Light Relay Circuit (C1A4B)
DESCRIPTION The skid control ECU (master cylinder solenoid)*1 or skid control ECU (brake actuator assembly)*2 sends a stop light operation request signal to the stop light relay (stop light switc ...

Front Radar Sensor Incorrect Axial Gap (C1A11)
DESCRIPTION When the vehicle is determined to be driving in a straight line or on a gradual curve based on signals from the yaw rate sensor, etc., the millimeter wave radar sensor assembly perfor ...

Other materials:

How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT HINT: Use the following procedure to troubleshoot the power window control system. *: Use the Techstream. PROCEDURE 1. VEHICLE BROUGHT TO WORKSHOP NEXT ...

Precaution
PRECAUTION 1. PRECAUTION (a) Before starting work on the fuel system, including inspections and repairs, disconnect the cable from the negative (-) battery terminal. (b) Do not smoke or work near fire when performing work on the fuel system. (c) Keep gasoline away from rubber or leather parts. ...

Short to +B in Outer Mirror Indicator(Slave) (C1AB1)
DESCRIPTION This DTC is stored when the blind spot monitor sensor RH detects a +B short in the blind spot monitor indicator RH. DTC Code DTC Detection Condition Trouble Area C1AB1 With the blind spot monitor main switch assembly (warni ...

В© 2011-2024 Copyright www.ttguide.net