DESCRIPTION
The forward recognition camera receives steering angle information from the spiral cable with sensor sub-assembly. If the forward recognition camera detects a spiral cable with sensor sub-assembly, DTC C1A47 is stored.
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
---|---|---|---|
C1A47 |
Steering Angle Sensor |
When the vehicle is being driven at a speed of 5 km/h (3 mph) or more 3 seconds after the ignition switch is turned to ON, a signal from the spiral cable with sensor sub-assembly indicating that there is a spiral cable with sensor sub-assembly malfunction is detected by the forward recognition camera for 5 seconds or more. |
|
CAUTION / NOTICE / HINT
NOTICE:
Click here
Click here
PROCEDURE
1. |
CHECK DTC OUTPUT (VEHICLE STABILITY CONTROL SYSTEM) |
HINT:
If the steering angle sensor is malfunctioning, DTCs for the vehicle stability control system will be stored. Troubleshoot the vehicle stability control system first.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Check for DTCs.
Click here
Click here
Result |
Proceed to |
---|---|
Vehicle stability control system DTCs are not output |
A |
Vehicle stability control system DTCs are output (for Vacuum Brake Booster) |
B |
Vehicle stability control system DTCs are output (for Hydraulic Brake Booster) |
C |
B |
GO TO VEHICLE STABILITY CONTROL SYSTEM |
C |
GO TO VEHICLE STABILITY CONTROL SYSTEM |
|
2. |
CHECK DTC OUTPUT |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / LKA/LDA / Trouble Codes.
(e) Clear the DTCs.
Click here
(f) Make sure that the DTC detection conditions are met.
HINT:
If the following procedure is not performed, the previously output DTC cannot be detected.
(g) Check for DTCs.
Click here
Result |
Proceed to |
---|---|
DTC C1A47 is output |
A |
DTC C1A47 is not output |
B |
B |
USE SIMULATION METHOD TO CHECK |
|
3. |
REPLACE FORWARD RECOGNITION CAMERA |
(a) Replace the forward recognition camera.
Click here
(b) Adjust the forward recognition camera.
Click here
|
4. |
CHECK DTC OUTPUT |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / LKA/LDA / Trouble Codes.
(e) Clear the DTCs.
Click here
(f) Make sure that the DTC detection conditions are met.
HINT:
If the following procedure is not performed, the previously output DTC cannot be detected.
(g) Check for DTCs.
Click here
Result |
Proceed to |
---|---|
DTC C1A47 is output |
A |
DTC C1A47 is not output |
B |
A |
REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY |
B |
END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE) |
Utility
UTILITY
NOTICE:
When replacing the millimeter wave radar sensor assembly, always replace
it with a new one. If a millimeter wave radar sensor assembly which was
installed to another vehicle is used, the information stored in it will
not match the information from the vehicle. A ...
Clutch Release Cylinder(for Rc62f)
Components
COMPONENTS
ILLUSTRATION
Disassembly
DISASSEMBLY
PROCEDURE
1. REMOVE CLUTCH RELEASE CYLINDER KIT
(a) Remove the boot from the cylinder body.
(b) Remove the push rod from the boot.
(c) Using compressed air, remove the piston together with the spring
from the cy ...
Immobiliser System does not Operate Properly
DESCRIPTION
The engine immobiliser system compares the ID code that is registered in the
certification ECU (smart key ECU assembly) with the ID code of the transponder chip
that is embedded in the electrical key transmitter sub-assembly.
WIRING DIAGRAM
(See page ).
CAUTION / NOTICE / HINT
...