Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: SRS Warning Light Remains ON

DESCRIPTION

The SRS warning light is located on the combination meter assembly.

When the SRS condition is normal, the SRS warning light illuminates for approximately 6 seconds after the ignition switch is turned from off to ON, and then turns off automatically.

If there is a malfunction in the SRS, the SRS warning light illuminates or blinks to inform the driver of the problem. When terminals TC and CG of the DLC3 are connected, the SRS warning light blinks to indicate DTCs.

The airbag sensor assembly is equipped with a voltage-increase circuit (DC-DC converter) in case the source voltage decreases. When the battery voltage decreases, the voltage-increase circuit (DC-DC converter) boosts the SRS voltage up to the normal level.

Malfunctions relating to battery voltage decreases cause the SRS warning light to illuminate. However, no DTCs are recorded in the airbag sensor assembly. The SRS warning light turns off automatically when the source voltage returns to normal.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION / NOTICE / HINT

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page ). ).

PROCEDURE

1.

CHECK FOR DTC (CAN COMMUNICATION SYSTEM)

(a) Turn the ignition switch to ON.

(b) Check the DTCs (See page OK: ).

OK:

DTC is not output.

NG

GO TO CAN COMMUNICATION SYSTEM

OK

2.

INSPECT BATTERY

(a) Measure the voltage of the battery.

Standard Voltage:

Tester Connection

Condition

Specified Condition

Battery

Always

11 to 14 V

NG

CHECK AND REPLACE BATTERY OR CHARGING SYSTEM

OK

3.

CHECK CONNECTION OF CONNECTORS

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Check that the connectors are properly connected to the airbag sensor assembly and combination meter assembly.

OK:

The connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY

OK

4.

CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF AIRBAG SENSOR ASSEMBLY)

(a) Disconnect the connector from the airbag sensor assembly.

(b) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

(c) Turn the ignition switch to ON.

(d) Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).

(e) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

A21-21 (IG2) - A21-25 (E1)

Ignition switch ON

11 to 14 V

A21-21 (IG2) - A21-26 (E2)

Ignition switch ON

11 to 14 V

Text in Illustration

*a

Front view of wire harness connector

(to Airbag Sensor Assembly)

NG

REPLACE HARNESS AND CONNECTOR

OK

5.

CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER ASSEMBLY)

(a) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(b) Disconnect the connector from the combination meter assembly.

(c) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

(d) Turn the ignition switch to ON.

(e) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

C9-20 (IG+) - C9-18 (ES)

Ignition switch ON

11 to 14 V

Text in Illustration

*a

Front view of wire harness connector

(to Combination Meter Assembly)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

6.

CHECK SRS WARNING LIGHT

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Connect the connector to the combination meter assembly.

(d) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

(e) Turn the ignition switch to ON.

(f) Check the SRS warning light condition.

OK:

The SRS warning light turns off after the primary check period and comes on again after approximately 10 seconds.

HINT:

The primary check period lasts for approximately 6 seconds after the ignition switch is turned to ON.

OK

REPLACE AIRBAG SENSOR ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

SRS Warning Light does not Come ON
DESCRIPTION See page . WIRING DIAGRAM See page . CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to this system before performing the following inspection pr ...

TC and CG Terminal Circuit
DESCRIPTION DTC output mode is set by connecting terminals TC and CG of the DLC3. The DTCs are displayed by blinking the SRS warning light. HINT: Make sure that DTCs which relate to the CA ...

Other materials:

Power Source Circuit
DESCRIPTION This circuit provides power to operate the forward recognition camera. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to this system before performing the following inspection procedure. PROCEDURE 1. CHECK HARNESS A ...

Disassembly
DISASSEMBLY CAUTION / NOTICE / HINT HINT: Use the same procedure for both the LH and RH sides. The procedure described below is for the LH side. PROCEDURE 1. REMOVE FOG LIGHT BULB (a) Turn the fog light bulb in the direction indicated by the arrow in the illust ...

Inspection
INSPECTION PROCEDURE 1. INSPECT OUTER MIRROR LH (a) Check the outer mirror heater operation. Text in Illustration *a Component without harness connected (Outer Mirror LH) (1) Measure the resistance according to the value(s) ...

В© 2011-2024 Copyright www.ttguide.net