Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Speaker Output Short (B15C3)

DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No.

DTC Detection Condition

Trouble Area

B15C3

A short is detected in the speaker output circuit.

  • Harness or connector
  • Speaker
  • Radio and display receiver assembly

WIRING DIAGRAM

PROCEDURE

PROCEDURE

1.

CONFIRM MODEL

(a) Choose the model to be inspected.

Result

Result

Proceed to

for 6 Speakers

A

for 4 Speakers

B

B

GO TO STEP 8

A

2.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)

(a) Disconnect the R30 and R29 radio and display receiver assembly connectors.

(b) Disconnect the S46 and S47 front No. 2 speaker assembly connectors.

(c) Disconnect the S17 and S18 rear speaker assembly connectors.

(d) Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:

Tester Connection

Condition

Specified Condition

R30-1 (FR+) - Body ground

Always

10 kΩ or higher

R30-5 (FR-) - Body ground

Always

10 kΩ or higher

R30-2 (FL+) - Body ground

Always

10 kΩ or higher

R30-6 (FL-) - Body ground

Always

10 kΩ or higher

R29-1 (RR+) - Body ground

Always

10 kΩ or higher

R29-3 (RR-) - Body ground

Always

10 kΩ or higher

R29-2 (RL+) - Body ground

Always

10 kΩ or higher

R29-6 (RL-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.

CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND)

(a) Disconnect the S15 and S16 front No. 1 speaker assembly connectors.

(b) Disconnect the S46 and S47 front No. 2 speaker assembly connectors.

(c) Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

Standard Resistance:

Tester Connection

Condition

Specified Condition

S47-1 (+) - Body ground

Always

10 kΩ or higher

S47-3 (-) - Body ground

Always

10 kΩ or higher

S46-1 (+) - Body ground

Always

10 kΩ or higher

S46-3 (-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

4.

INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

(a) Remove the front No. 1 speaker assembly (See page ).

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 - 2

Always

3.2 to 4.8 Ω

Text in Illustration

*a

Component without harness connected

(Front No. 1 Speaker Assembly)

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

OK

5.

INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

(a) Remove the front No. 2 speaker assembly (See page ).

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

2 (+) - 4 (-)

Always

10 kΩ or higher

2 (+) - 1 (+)

Always

Below 1 Ω

4 (-) - 3 (-)

Always

Below 1 Ω

Text in Illustration

*a

Component without harness connected

(Front No. 2 Speaker Assembly)

NG

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

OK

6.

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

(a) Replace the front No. 2 speaker assembly with a new or known good one (See page (b) Clear the DTCs (See page  ). ).

(b) Clear the DTCs (See page (c) Recheck for DTCs and check that no DTCs are output. ).

(c) Recheck for DTCs and check that no DTCs are output.

OK:

No DTCs are output.

HINT:

  • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
  • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
  • Perform the above inspection on both the LH and RH side.
OK

END

NG

7.

INSPECT REAR SPEAKER ASSEMBLY

(a) Remove the rear speaker assembly (See page ). ).

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 - 2

Always

4 Ω

Text in Illustration

*a

Component without harness connected

(Rear Speaker Assembly)

OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE REAR SPEAKER ASSEMBLY

8.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND)

(a) Disconnect the R30 radio and display receiver assembly connector.

(b) Disconnect the S46 and S47 front No. 2 speaker assembly connectors.

(c) Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.

Standard Resistance:

Tester Connection

Condition

Specified Condition

R30-1 (FR+) - Body ground

Always

10 kΩ or higher

R30-5 (FR-) - Body ground

Always

10 kΩ or higher

R30-2 (FL+) - Body ground

Always

10 kΩ or higher

R30-6 (FL-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

9.

CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND)

(a) Disconnect the S15 and S16 front No. 1 speaker assembly connectors.

(b) Disconnect the S46 and S47 front No. 2 speaker assembly connectors.

(c) Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.

Standard Resistance:

Tester Connection

Condition

Specified Condition

S46-1 (+) - Body ground

Always

10 kΩ or higher

S46-3 (-) - Body ground

Always

10 kΩ or higher

S47-1 (+) - Body ground

Always

10 kΩ or higher

S47-3 (-) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

10.

INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

(a) Remove the front No. 1 speaker assembly (See page ).

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 - 2

Always

3.2 to 4.8 Ω

Text in Illustration

*a

Component without harness connected

(Front No. 1 Speaker Assembly)

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

OK

11.

INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

(a) Remove the front No. 2 speaker assembly (See page ).

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

2 (+) - 4 (-)

Always

10 kΩ or higher

2 (+) - 1 (+)

Always

Below 1 Ω

4 (-) - 3 (-)

Always

Below 1 Ω

Text in Illustration

*a

Component without harness connected

(Front No. 2 Speaker Assembly)

NG

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

OK

12.

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

(a) Replace the front No. 2 speaker assembly with a new or known good one (See page (b) Clear the DTCs (See page  ). ).

(b) Clear the DTCs (See page (c) Recheck for DTCs and check that no DTCs are output. ).

(c) Recheck for DTCs and check that no DTCs are output.

OK:

No DTCs are output.

HINT:

  • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
  • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
  • Perform the above inspection on both the LH and RH side.
OK

END

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

Short in GPS Antenna (B15C0,B15C1)
DESCRIPTION These DTCs are stored when a malfunction occurs in the navigation antenna assembly. DTC No. DTC Detection Condition Trouble Area B15C0 ...

A/C ECU Vehicle Information Reading/Writing Processor Malfunction (B15F5)
DESCRIPTION This DTC is stored when items controlled by the air conditioning amplifier assembly cannot be customized via the audio and visual system vehicle customization screen. HINT: The air co ...

Other materials:

Personal Light Assembly
Components COMPONENTS ILLUSTRATION Installation INSTALLATION PROCEDURE 1. INSTALL MAP LIGHT BULB (a) Install the 2 map light bulbs to the 2 map light sockets. (b) Turn the 2 map light sockets with 2 map light bulbs in the direction indicated by the arrow shown in the ill ...

Operation Check
OPERATION CHECK INPUT SIGNAL CHECK *a +RES *b -SET *c ON-OFF *d CANCEL (a) Connect the Techstream to the DLC3. (b) Check the cruise control main switch using the Data List functio ...

Transmitter ID not Registered (C2171/71)
DESCRIPTION The IDs of each tire pressure warning valve and transmitter are registered to the tire pressure warning ECU and receiver. When the ECU detects that a transmitter ID code is not registered in the ECU, this DTC is stored. DTC No. Detection Item DTC D ...

© 2011-2024 Copyright www.ttguide.net