Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Side Turn Signal Light Assembly

Toyota Tacoma (2015-2018) Service Manual / Lighting / Side Turn Signal Light Assembly

Components

COMPONENTS

ILLUSTRATION

Removal

Removal

REMOVAL

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for both the RH and LH sides.
  • The procedure described below is for the LH side.

PROCEDURE

1. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

(See page 2. REMOVE OUTER MIRROR COVER )

2. REMOVE OUTER MIRROR COVER

3. REMOVE SIDE TURN SIGNAL LIGHT ASSEMBLY

3. REMOVE SIDE TURN SIGNAL LIGHT ASSEMBLY

(a) Remove the 2 screws.

(b) Disengage the 4 claws to separate the body cover with side turn signal light assembly.

(c) Disengage the guide to separate the wire harness.

(d) Disconnect the connector to remove the body cover with side turn signal light assembly.

(e) Disengage the 2 claws and 2 guides to remove the side turn signal light assembly.

Inspection

INSPECTION

PROCEDURE

1. INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH

(a) Check the illuminates.

(1) Apply battery voltage to the connector and check the light illumination condition.

Text in Illustration

*a

Component without harness connected

(Side Turn Signal Light Assembly LH)

OK:

Measurement Condition

Specified Condition

Battery positive (+) → 1

Battery negative (-) → 2

Side turn signal light illuminates

If the result is not as specified, replace the side turn signal light assembly LH.

2. INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH

(a) Check the illuminates.

(1) Apply battery voltage to the connector and check the light illumination condition.

Text in Illustration

*a

Component without harness connected

(Side Turn Signal Light Assembly RH)

OK:

Measurement Condition

Specified Condition

Battery positive (+) → 1

Battery negative (-) → 2

Side turn signal light illuminates

If the result is not as specified, replace the side turn signal light assembly RH.

Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for both the LH and RH sides.
  • The procedure described below is for the LH side.

PROCEDURE

1. INSTALL SIDE TURN SIGNAL LIGHT ASSEMBLY

(a) Engage the 2 guides and 2 claws to install the side turn signal light assembly.

(b) Connect the connector.

(c) Engage the clamp to install the wire harness.

(d) Engage the 4 claws to install the body cover with side turn signal light assembly.

(e) Install the 2 screws.

2. INSTALL OUTER MIRROR COVER

3. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

3. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

(See page Stop Light Switch )

Room Light Assembly
Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE NO. 1 ROOM LIGHT ASSEMBLY (a) Using a screwdriver with its tip wrapped in protective tape, disengage ...

Stop Light Switch
Components COMPONENTS ILLUSTRATION Inspection INSPECTION PROCEDURE 1. INSPECT STOP LIGHT SWITCH (a) Check the resistance. (1) Measure the resistance using an ohmmeter, and check the re ...

Other materials:

Camshaft
Components COMPONENTS ILLUSTRATION ILLUSTRATION ILLUSTRATION ILLUSTRATION ILLUSTRATION *1 FUEL PUMP ASSEMBLY *2 FUEL PUMP LIFTER ASSEMBLY *3 FUEL PUMP LIFTER GUIDE *4 FUEL PUMP SPACER GAS ...

Precaution
PRECAUTION 1. IGNITION SWITCH EXPRESSIONS (a) The type of ignition switch used on this model differs according to the specifications of the vehicle. The expressions listed in the table below are used in this section. Expression Ignition Switch (Position) Engine ...

Cruise Control Switch Circuit
DESCRIPTION The cruise control main switch is used to turn the dynamic radar cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + ( ...

© 2011-2024 Copyright www.ttguide.net