DESCRIPTION
The cooler thermistor (room temperature sensor) is installed in the instrument panel to detect the cabin temperature which is used to control the air conditioning system AUTO mode. The resistance of the cooler thermistor (room temperature sensor) changes in accordance with the cabin temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.
The air conditioning amplifier assembly applies a voltage (5 V) to the cooler thermistor (room temperature sensor) and reads voltage changes due to changes in the resistance of the cooler thermistor (room temperature sensor).
DTC No. |
DTC Detection Condition |
Trouble Area |
---|---|---|
B1411/11 |
Open or short in cooler thermistor (room temperature sensor) circuit |
|
WIRING DIAGRAM
PROCEDURE
1. |
READ VALUE USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Air Conditioner / Data List.
(e) Check the value(s) by referring to the table below.
Air Conditioner
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
---|---|---|---|
Room Temperature Sensor |
Cooler thermistor (room temperature sensor) / min.: -6.50°C (20.30°F) max.: 57.25°C (135.05°F) |
Actual cabin temperature displayed |
- |
OK:
The display is as specified in the Normal Condition column.
Result |
Proceed to |
---|---|
NG |
A |
OK (When troubleshooting according to Problem Symptoms Table) |
B |
OK (When troubleshooting according to the DTC) |
C |
B |
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
C |
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY |
|
2. |
INSPECT COOLER THERMISTOR (ROOM TEMPERATURE SENSOR) |
(a) Remove the cooler thermistor (room temperature sensor) (See page ).
(b) Inspect the cooler thermistor (room temperature sensor) (See page ).
NG |
REPLACE COOLER THERMISTOR (ROOM TEMPERATURE SENSOR) |
|
3. |
CHECK HARNESS AND CONNECTOR (COOLER THERMISTOR (ROOM TEMPERATURE SENSOR) - AIR CONDITIONING AMPLIFIER ASSEMBLY) |
(a) Disconnect the R36 cooler thermistor (room temperature sensor) connector.
(b) Disconnect the A36 air conditioning amplifier assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
R36-1 - A36-16 (TR) |
Always |
Below 1 Ω |
R36-2 - A36-26 (SG-1) |
Always |
Below 1 Ω |
R36-1 or A36-16 (TR) - Body ground |
Always |
10 kΩ or higher |
R36-2 or A36-26 (SG-1) - Body ground |
Always |
10 kΩ or higher |
OK |
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. CHECK FUEL PUMP ASSEMBLY OPERATION
(a) Check fuel pressure.
(1) Connect the Techstream to the DLC3.
(2) Start the engine.
(3) Turn the Techstream on.
(4) Enter the following menus: Powertrain / Engine / Active Test / Control the
Target Fuel Pressure.
(5) ...
Additional Key cannot be Registered
DESCRIPTION
If additional registration is not possible, a malfunction in the certification
ECU (smart key ECU assembly), engine switch, electrical key transmitter sub-assembly
or steering lock ECU (steering lock actuator or UPR bracket assembly) is suspected.
CAUTION / NOTICE / HINT
NOTICE ...
Voice Recognition Microphone Disconnected (B1579)
DESCRIPTION
The radio and display receiver assembly and telephone microphone assembly are
connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.
DTC Code
DTC Det ...