Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Replacement

REPLACEMENT

PROCEDURE

1. REPLACE INTAKE VALVE GUIDE BUSH

(a) Heat the cylinder head to 80 to 100°C (176 to 212°F).

(b) Place the cylinder head on wooden blocks.

(c) Using SST and a hammer, tap out the intake valve guide bushes.

SST: 09201-10000

09201-01050

SST: 09950-70010

09951-07100

(d) Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head.

Standard cylinder bore diameter:

10.285 to 10.306 mm (0.4049 to 0.4057 in.)

Select a New Guide Bush (STD or O/S 0.05):

Bush Size

Specified Condition

STD

10.285 to 10.306 mm (0.4049 to 0.4057 in.)

O/S 0.05

10.335 to 10.356 mm (0.4069 to 0.4077 in.)

If the bush bore diameter of the cylinder head is more than 10.306 mm (0.4057 in.), machine the bush bore to the dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 valve guide bush.

If the bush bore diameter of the cylinder head is more than 10.356 mm (0.4077 in.), replace the cylinder head.

(e) Heat the cylinder head to 80 to 100°C (176 to 212°F).

(f) Place the cylinder head on wooden blocks.

(g) Using SST, tap in new intake valve guide bushes to the specified protrusion height.

Text in Illustration

*a

Protrusion Height

SST: 09201-10000

09201-01050

SST: 09950-70010

09951-07100

Standard protrusion height:

9.10 to 9.90 mm (0.358 to 0.390 in.)

(h) Using a sharp 5.5 mm reamer, ream the valve guide bushings to obtain the specified clearance.

Standard oil clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)

2. REPLACE EXHAUST VALVE GUIDE BUSH

(a) Heat the cylinder head to 80 to 100°C (176 to 212°F).

(b) Place the cylinder head on wooden blocks.

(c) Using SST and a hammer, tap out the exhaust valve guide bushes.

SST: 09201-10000

09201-01050

SST: 09950-70010

09951-07100

(d) Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head.

Standard cylinder bore diameter:

10.285 to 10.306 mm (0.4049 to 0.4057 in.)

Select a New Guide Bush (STD or O/S 0.05):

Bush Size

Specified Condition

STD

10.285 to 10.306 mm (0.4049 to 0.4057 in.)

O/S 0.05

10.335 to 10.356 mm (0.4069 to 0.4077 in.)

If the bush bore diameter of the cylinder head is more than 10.306 mm (0.4057 in.), machine the bush bore to the dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 valve guide bush.

If the bush bore diameter of the cylinder head is more than 10.356 mm (0.4077 in.), replace the cylinder head.

(e) Heat the cylinder head to 80 to 100°C (176 to 212°F).

(f) Place the cylinder head on wooden blocks.

(g) Using SST, tap in new exhaust valve guide bushes to the specified protrusion height.

Text in Illustration

*a

Protrusion Height

SST: 09201-10000

09201-01050

SST: 09950-70010

09951-07100

Standard protrusion height:

9.10 to 9.90 mm (0.358 to 0.390 in.)

(h) Using a sharp 5.5 mm reamer, ream the valve guide bushings to obtain the specified clearance.

Standard oil clearance:

0.03 to 0.065 mm (0.00118 to 0.00256 in.)

3. REPLACE RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.

(a) Using a plastic-faced hammer, tap in new ring pins to the specified protrusion height.

Text in Illustration
   

*A

Bank 1

*B

Bank 2

*a

Protrusion Height

Standard protrusion height:

2.5 to 3.5 mm (0.0984 to 0.138 in.)

4. REPLACE STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pin unless it is being replaced.

(a) Using a plastic-faced hammer, tap in new straight pins as shown in the illustration.

Text in Illustration

*A

Bank 1

*B

Bank 2

*a

Protrusion Height

-

-

Standard protrusion height:

17.5 to 19.5 mm (0.689 to 0.768 in.)

Inspection
INSPECTION PROCEDURE 1. INSPECT CYLINDER HEAD SUB-ASSEMBLY (a) Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces where the cylinder head contacts the cy ...

Reassembly
REASSEMBLY CAUTION / NOTICE / HINT HINT: Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly or cylinder head LH (See page ). PROCEDURE 1. INSTALL SPARK ...

Other materials:

Rear Right Sensor Malfunction (C1AE9)
DESCRIPTION The No. 1 ultrasonic sensor (rear corner sensor RH) is installed on the rear bumper. The ECU detects obstacles based on signals received from the No. 1 ultrasonic sensor (rear corner sensor RH). If the No. 1 ultrasonic sensor (rear corner sensor RH) has an open circuit or other ma ...

Installation
INSTALLATION PROCEDURE 1. INSTALL ENGINE COOLANT TEMPERATURE SENSOR 2. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY 3. INSTALL IGNITION COIL ASSEMBLY 4. INSTALL FUEL INJECTOR SEAL 5. INSTALL FUEL INJECTOR ASSEMBLY 6. INSTALL FUEL DELIVERY PIPE RH 7. INSTALL FUEL DELIVERY PIP ...

Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC) (C1281,...,C1458)
DESCRIPTION DTC Code DTC Detection Condition Trouble Area C1281 Stored only during test mode. Master cylinder pressure sensor circuit Skid control ECU, master cylinder pressure sensor (master cylinder s ...

© 2011-2024 Copyright www.ttguide.net