Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Removal

REMOVAL

PROCEDURE

1. REMOVE FRONT FENDER SEAL RH

HINT:

Use the same procedure as for the LH side (See page 2. REMOVE V-BANK COVER SUB-ASSEMBLY ).

2. REMOVE V-BANK COVER SUB-ASSEMBLY

3. REMOVE AIR CLEANER CAP AND HOSE 3. REMOVE AIR CLEANER CAP AND HOSE

3. REMOVE AIR CLEANER CAP AND HOSE

4. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

4. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

(a) Remove the engine oil level dipstick.

(b) Disengage the clamp to separate the wire harness.

(c) Remove the bolt and engine oil level dipstick guide from the timing chain cover assembly and oil pan sub-assembly.

(d) Remove the O-ring from the engine oil level dipstick guide.

5. REMOVE THROTTLE BODY BRACKET

(a) Remove the 2 bolts and throttle body bracket from the intake air surge tank assembly and timing chain cover assembly.

6. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1)

(a) Disconnect the connector from the camshaft timing oil control solenoid assembly.

(b) Remove the 2 bolts and camshaft timing oil control solenoid assembly from the timing chain cover assembly.

(c) Remove the O-ring from the camshaft timing oil control solenoid assembly.

HINT:

  • Make sure to remove the O-ring completely, as the O-ring may remain on the timing chain cover assembly side.
  • Do not drop the O-ring into the timing chain cover assembly.

7. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1)

(a) Disconnect the connector from the camshaft timing oil control solenoid assembly.

(b) Remove the 2 bolts and camshaft timing oil control solenoid assembly from the timing chain cover assembly.

(c) Remove the O-ring from the camshaft timing oil control solenoid assembly.

HINT:

  • Make sure to remove the O-ring completely, as the O-ring may remain on the timing chain cover assembly side.
  • Do not drop the O-ring into the timing chain cover assembly.

8. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)

(a) Disconnect the connector from the camshaft timing oil control solenoid assembly.

(b) Remove the 2 bolts and camshaft timing oil control solenoid assembly from the timing chain cover assembly.

(c) Remove the O-ring from the camshaft timing oil control solenoid assembly.

HINT:

  • Make sure to remove the O-ring completely, as the O-ring may remain on the timing chain cover assembly side.
  • Do not drop the O-ring into the timing chain cover assembly.

9. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2)

(a) Disconnect the connector from the camshaft timing oil control solenoid assembly.

(b) Remove the 2 bolts and camshaft timing oil control solenoid assembly from the timing chain cover assembly.

(c) Remove the O-ring from the camshaft timing oil control solenoid assembly.

HINT:

  • Make sure to remove the O-ring completely, as the O-ring may remain on the timing chain cover assembly side.
  • Do not drop the O-ring into the timing chain cover assembly.
Inspection
INSPECTION PROCEDURE 1. INSPECT CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (a) Check the operation. (1) Apply battery voltage between the terminals and check that the plunger ope ...

Installation
INSTALLATION PROCEDURE 1. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1) (a) Apply engine oil to a new O-ring and install it to the camshaft timing ...

Other materials:

Rear Speed Sensor
Removal REMOVAL PROCEDURE 1. PRECAUTION NOTICE: After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notic ...

Key information
The following keys are provided with the vehicle. Vehicles without engine immobilizer system Master keys Key number plate Vehicles with engine immobilizer system Master keys Key number plate ■Key number plate Keep the plate in a safe place such as your wallet, not in the v ...

Installation
INSTALLATION PROCEDURE 1. ADJUST COMPRESSOR OIL (a) for HFC-134a (R134a): (1) When replacing the compressor and magnetic clutch with new ones, after gradually discharging the refrigerant gas from the service valve, drain the following volume of oil from new compressor and magnetic clutch bef ...

В© 2011-2024 Copyright www.ttguide.net