Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Removal

REMOVAL

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for the LH side and RH side.
  • The following procedure listed is for the LH side.

PROCEDURE

1. REMOVE FRONT WHEEL

2. DRAIN BRAKE FLUID

NOTICE:

Immediately wash off any brake fluid that comes into contact with any painted surfaces.

3. REMOVE FRONT DISC BRAKE ANTI-RATTLE WITH HOLE PIN

(a) for Pin Hold Clip Type A:

(1) Remove the pin hold clip from the 2 front disc brake anti-rattle with hole pins.

Text in Illustration

*1

Front Disc Brake Anti-rattle with Hole Pin

*2

Pin Hold Clip

*3

Anti-rattle Spring

NOTICE:

The pin hold clip can be used again if it has sufficient rebound; no deformation or wear; and has had all rust, dirt and foreign matter cleaned off.

(2) Remove the 2 front disc brake anti-rattle with hole pins from the disc brake cylinder assembly.

(3) Remove the anti-rattle spring from the front disc brake pad.

NOTICE:

The anti-rattle spring can be used again if it has sufficient rebound; no deformation, cracks or wear; and has had all rust, dirt and foreign matter cleaned off.

(b) for Pin Hold Clip Type B:

(1) Remove the 2 pin hold clips from the 2 front disc brake anti-rattle with hole pins.

Text in Illustration

*1

Front Disc Brake Anti-rattle with Hole Pin

*2

Pin Hold Clip

*3

Anti-rattle Spring

(2) Remove the 2 front disc brake anti-rattle with hole pins from the disc brake cylinder assembly.

(3) Remove the anti-rattle spring from the front disc brake pad.

NOTICE:

The anti-rattle spring can be used again if it has sufficient rebound; no deformation, cracks or wear; and has had all rust, dirt and foreign matter cleaned off.

4. REMOVE FRONT DISC BRAKE PAD KIT

(a) Remove the 2 front disc brake pads with front anti squeal shim from the disc brake cylinder assembly.

5. REMOVE FRONT ANTI SQUEAL SHIM KIT

(a) Remove the 2 front anti squeal shims from each of the front disc brake pads.

6. REMOVE DISC BRAKE CYLINDER ASSEMBLY

(a) Using a union nut wrench 10 mm, separate the brake tube from the disc brake

(a) Using a union nut wrench 10 mm, separate the brake tube from the disc brake cylinder assembly.

HINT:

Use a container to collect the brake fluid as it drains out.

(b) Remove the 2 bolts and the disc brake cylinder assembly.

7. INSPECT DISC THICKNESS

(a) Using a micrometer, measure the disc thickness.

(a) Using a micrometer, measure the disc thickness.

Standard thickness:

28.0 mm (1.10 in.)

Minimum thickness:

26.0 mm (1.03 in.)

If the disc thickness is less than the minimum, replace the front disc.

8. REMOVE FRONT DISC

(a) Place matchmarks on the front disc and the front axle hub and remove the

(a) Place matchmarks on the front disc and the front axle hub and remove the front disc.

Text in Illustration

*a

Matchmark

Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE CYLINDER BOOT (a) Using a screwdriver, remove the 4 cylinder boots from the caliper. 2. REMOVE FRONT DISC BRAKE PISTON (a) Prepare a wooden plate to hold the p ...

Inspection
INSPECTION PROCEDURE 1. INSPECT BRAKE CYLINDER AND PISTON (a) Check the cylinder bore and piston for rust and scoring. 2. INSPECT PAD LINING THICKNESS (a) Using a ruler, measure the pad lining ...

Other materials:

Rear Right Sensor Malfunction (C1AE9)
DESCRIPTION The No. 1 ultrasonic sensor (rear corner sensor RH) is installed on the rear bumper. The ECU detects obstacles based on signals received from the No. 1 ultrasonic sensor (rear corner sensor RH). If the No. 1 ultrasonic sensor (rear corner sensor RH) has an open circuit or other ma ...

Operation Check
OPERATION CHECK 1. CHECK WINDOW LOCK SWITCH HINT: Before performing the window lock switch operation check, make sure that the window lock switch is off (the switch is not pushed in). (a) Check that the front passenger and rear windows cannot be operated from each power window regulator swit ...

Lost Communication With Vehicle Dynamics Control Module (U0122)
DESCRIPTION This DTC is detected if communication is lost with the skid control ECU (brake actuator assembly). DTC No. Detection Item DTC Detection Condition Trouble Area U0122 Lost Communication with Vehicle Dynamics Contro ...

В© 2011-2024 Copyright www.ttguide.net