Toyota Tacoma (2015-2018) Service Manual: Removal
REMOVAL
PROCEDURE
1. REMOVE SLIDING ROOF SIDE GARNISH LH
(a) Fully open the sunshade trim sub-assembly.
|
(b) Remove the sliding roof side garnish LH. |
|
2. REMOVE SLIDING ROOF SIDE GARNISH RH
HINT:
Use the same procedure as for the LH side.
3. REMOVE SLIDING ROOF GLASS SUB-ASSEMBLY
|
(a) Using a T25 "TORX" socket wrench, remove the 4 screws and sliding roof glass sub-assembly. NOTICE: To prevent the sliding roof glass and sliding roof drive gear from being displaced, fully close the sliding roof glass (sliding roof drive cable), and then remove the sliding roof drive gear. HINT: The illustration shows the LH side. The vertical orientation of the RH side is opposite that of the image shown in the illustration. |
|
4. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH (for Double Cab)
(See page .gif)
)
5. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH (for Double Cab)
HINT:
Use the same procedure as for the LH side.
6. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH (for Access Cab)
(See page
)
7. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH (for Access Cab)
HINT:
Use the same procedure as for the LH side.
8. REMOVE ROOF PANEL SUPPORT LH (for Front Side)
|
(a) Remove the bolt, nut and roof panel support LH. |
|
9. REMOVE ROOF PANEL SUPPORT RH (for Front Side)
HINT:
Use the same procedure as for the LH side.
10. REMOVE ROOF PANEL SUPPORT LH (for Rear Side)
|
(a) Remove the 2 bolts and roof panel support LH. |
|
11. REMOVE ROOF PANEL SUPPORT RH (for Rear Side)
HINT:
Use the same procedure as for the LH side.
12. REMOVE SLIDING ROOF HOUSING BRACKET LH
|
(a) Remove the 6 bolts and sliding roof housing bracket LH. |
|
13. REMOVE SLIDING ROOF HOUSING BRACKET RH
HINT:
Use the same procedure as for the LH side.
14. REMOVE SLIDING ROOF HOUSING SUB-ASSEMBLY
|
(a) Slide the clip and disconnect front side of the 2 sliding roof drain hoses. HINT: The illustration shows the LH side. The vertical orientation of the RH side is opposite that of the image shown in the illustration. |
|
|
(b) Slide the clip and disconnect rear side of the 2 rear sliding roof drain hoses. HINT: The illustration shows the LH side. The vertical orientation of the RH side is opposite that of the image shown in the illustration. |
|
(c) Remove the 8 nuts and sliding roof housing sub-assembly.
15. REMOVE SLIDING ROOF WEATHERSTRIP
|
(a) Remove the sliding roof weatherstrip from the sliding roof glass. |
|
Disassembly
DISASSEMBLY
PROCEDURE
1. REMOVE ROOM LIGHT BRACKET
(a) Disengage the guide to remove the room light bracket.
2. REMOVE SLIDING ROOF DRIVE GEAR ...
Sliding Roof Switch Assembly
Components
COMPONENTS
ILLUSTRATION
Installation
INSTALLATION
PROCEDURE
1. INSTALL SLIDING ROOF SWITCH ASSEMBLY (ROOF CONSOLE BOX ASSEMBLY)
(a) Connect the connector.
(b) Engage the 4 cli ...
Other materials:
Adjusting the position of the air outlets
Center outlets
Direct air flow to the left or right, up or down.
Right and left side outlets
Direct air flow to the left or right, up or down.
Opening and closing the air outlets
Center outlets
Open the vent.
Close the vent.
Right and left side outlets
Open the vent.
...
Wireless Door Lock Buzzer
Components
COMPONENTS
ILLUSTRATION
Removal
REMOVAL
PROCEDURE
1. REMOVE WIRELESS DOOR LOCK BUZZER
(a) Disconnect the connector.
(b) Using a clip remover, disengage the clamp to remove the wireless door lock
buzzer.
Installation
...
Check For Intermittent Problems
CHECK FOR INTERMITTENT PROBLEMS
1. CHECK FOR INTERMITTENT PROBLEMS
HINT:
A momentary interruption (open circuit) in the connectors and/or wire harnesses
between the sensors and ECUs can be detected using the ECU Data List function of
the Techstream.
(a) Turn the ignition switch off.
(b) Con ...
